The fold away tine pivot or clip holds the tine rows in place. This part is made of gray plastic and is approximately 3 and a half inches in length. Some dishwasher models will have fold away tine row...
This part is essential in your dishes getting clean during the wash cycle. If there is any debris or a tear in the filter, it can cause extra buildup and, therefore, causing dirty dishes.
This is the replacement convertible tine pivot for your dishwasher. It is made of gray plastic and is approximately 4 inches long and 1 inch wide. The convertible tine pivot allows the tine row to eit...
The docking station is located on the water supply tube at the far back. It provides water to the upper and middle spray arm and also includes the flappers.
This hose clamp extends from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag brand washing machines.
$11.80
In Stock
Questions And Answers for MDB7600AWB
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Aaron
February 15, 2020
My dishwasher starts filling and begins cycle for a few seconds and then stops. It does this every ten seconds four or five times and then shuts down. Why?
For model number MDB7600AWB
Hello and thank you for writing.
It certainly sounds like it could be a faulty door handle assembly PS11748729 and/or possibly a malfunctioning door switch PS11747715 you should check the part(s) for signs of damage or test with a multimeter, and replace the part(s) as needed. We hope this helps. Please contact us anytime if you require further assistance.
Hi Sandy,
Thank you for your question. If your dishwasher is not draining, there are some parts that you will need to check to see which one is causing the issue. You will need to check the drain pump, the accumulator filter, the drain pump valve flapper, the drain pump inlet flapper and the wash impeller. We have included a link that you may reference on how to check these parts and some others as well. Once you have determined the part you need, please feel free to call customer service. We are open 7 days a week and anyone will be happy to assist you. We look forward to hearing from you!
The hardest thing was figuring out that you only need to purchase the latch handle because it only comes as a complete latch assembly, why they even list the latch assembly as a separate part in the parts list stupid. (you get the handle and latch already put together and it cost less than the latch assembly without the handle). Anyway all you need to do is disconect the power from the dishwasher (unless you like to live dangerously like me) take your drill with the correct size torx bit and remove all the screws on the inside door pannel (the top center two screws actually hold the latch assembly in place). Disconect the 4 wires from the old part and reconect them to the new part and reinstall all the torx screws being careful not to strip the plastic threads that they screw into if you are using a drill. Whole process takes less than 5 minutes. I am surprised that Maytag used such a flimsy handle assembly in their dishwashers since they are supposed to have the repair men with the most time on their hands. They probably sell just as many handle assemblies as they do dishwashers that have this particular part in it, probably more since you will probably have to change it 2 or 3 times during the life of the unit.
I Followed others' instructions already posted to replace the whole handle assembly. In particular, use a big screwdriver placed against the bottom of the handle and whack the grip with the palm of your hand to get the handle to move back to the open position so you can open the door and start the job. I am no handyman, but this fix was easy, about 30 minutes in all, most of which was spent figuring out which breaker to pull so as not to get shocked. One note of caution: use the correct screwdriver attachment (not a Phillips head or regular, but a star or something- see I am not a handyman but I do have a $15 screwdriver set that just paid for itself 10 times over!).
Remove the 8 or 9 torx screws holding the inner and outer door assembly together (leave the bottom screws in), lift the old handle assembly out, transfer the switches to the new handle assembly, and reassemble door.
.gif "SUPPLEMENTAL INFORMATION Diagram and Parts List for Maytag Dishwasher")
