MAT12PDDBW Maytag Washer - Instructions

I propped up the machine. Turned the water off .took the pump belt off, then took the two hose clamps off. With a bucket and towels on hand for left over water in the hoses, i removed the two hoses. Then removed three screws that held the pump on. Installed the new pump in reverse order.

Tilt washer. Remove old belts. Put in new. Tighten transmission bet and pump belt per YouTube. It works like new now.

Install belts.

I replaced the 3 screws because they were rusty. Then I replaced the Drain pump

Followed the first guys directions.
remove front
lift top
remove agitator
remove locking nut clockwise
remove inner tub
remove Mounting S loosen set screw and clockwise also
clean well
replace boot as shown in tip in sheet
push boot on completely

Found the parts I needed on your website along with a video that showed exactly how to do the repair. Set my iPad on the dryer and followed along step by step. Never would have tried something like this without your helpful information.

befor start i make sure whether i can repair or not.then i order the part which is fit with what i wont to repair.by checking siriel number . then repairng is very easy.

Loosened the set screw and removed the agitator, found nothing wrong. Replaced the agitator and tightened set screw, no more wobble.
This is a mid 1970 Maytag and a workhorse.Had three kids wash over the years, now "kids" in their late 30's and early 40' and washer is as good as new (except a little rusty)

First time I had a problem with it. Sometimes just look for the simple things !

Part select refunded me for my part that I ordered very fast.

Great Company to deal with!

Chalked the transmission with a pipe wrench. Removed the brake with grabbing on to it with vicegrips and hammered on the vicegrips to remove the brake. The new brake spun on after the first two brakes didn't. Working great now!

Removed wet close and removed 99% of all the water with a simple sifon hose and sponges. Diconnected electric and water supply hoses. Layed washer on its back. Removed front of washer. Disconnected hoses to water pump and checked for blockage. None. You need to capture the risidual water from the hoses and the pump if you are working in an area that cannot tolerate spills. Pulled pump out (three screws) put a screwdriver and blocked the pump impellar and rotate the punps pully. Pully rotaded freely so the pump is bad. The two belts were pretty worn out so I replaced them also. Hooked up everything in reverse. Adjusted the tension of the belts as required. The drive belt for the pump should be pinched to 1/4". Checked the moter glides also. Put everything back together, checked for leaks and did a load of wash. Everything good. Dismanteling and diagnostics and clean up took about 30'. Assembly took another 30'. Purts fit perfectly.

First I took the door off. Undid two screws that held the top door on. Took the tub out. Make sure you have a spanner wrench. So much easier.

Based on info from website, sounded like it was the Belt Kit that needed replacing. While waiting for the Belt Kit, decided to take the Agitator out to have a "look-see". OMG! There was liquid fabric softener gunk so thick in, around, underneath the agitator that the unit could not get traction. The burning smell was the gunk getting hot as the agitator tried to work. After a thorough cleaning of the agitator and anything relating to it's ability to agitate, my Maytag is performing like it was brand new! I'm keeping the Belt Kit, because my washer is older and I've heard from friends and family that have purchased the new water restricted units, absolutely hate them; like the "low flow" toilets, instead of flushing once, you now have to flush 5 times. They are washing more smaller loads and double rinsing each load to get their clothes clean and free of residue. I'm a 69 year old woman who finds your website and your marvelous contributors an absolute Blessing!

Removed 2 Philip screws from bottom front panel. The belts came as a set, so pay attention to the belt sizes when replacing them. Have had the new belts installed now for a week or longer with no issues. Looks like a good fix.

First I bought a Maytag spanner wrench on eBay, you have to have it. It was $12.00 including shipping. Then when the parts showed up the next day followed the video and had it done in just under an hour from gathering my tools and cleaning up. The video was perfect and I had no troubles what so ever. The quote from the repair services was $280.00 and I did it for less than $90.00

Slipped on belts no tools needed.