MAH22PDAWW1 Maytag Washer - Instructions

The only issue I had was getting the hose from the tub re-installed, but that was my fault, the pump went right in. It couldn't have been easier. I was very pleased, received the replacement pump in just a couple of days, packaged very well for shipping, and had it installed in a matter of minutes. It took longer to take off front panel to access pump than it did to install it. Very pleased with "Part Select".....will use again!

Took less than 5 minutes to replace, So Happy;-)

Perfect part...saved me hundreds on labor. Thanks!

I pulled the front load washer away from the wall and unplugged. I tilted it back against the wall. I removed three screws from the lower front cover plate of washer. Once removed, I had access to the tub to pump hose which I found a small hole in. I went online to Partselect and found my part. The hose was connected in three different places by compression clamps. I then pulled the compression clamps off the connections. Cleaned up all connection points with a damp rag. Upon installation of the new tub to pump hose, I discarded the compression clamps and installed the new part using radiator clamps purchased at a auto parts store. Plugged washer back in and started a load too make sure all connections were good and tight with no leaks. After checking for leaks, I re-installed the front cover plate. Tilted washer back down being careful not too set it down hard or on my feet. Job Done....

Very --simple remove front acess panel -- open sump clean out remove water out of existing pump an hoses with small wet dry vac -- remove small wire harnes --cut band clamp on discharge with side cutter --remove inlet -suction side of pump hose clamp with channel locks --un bolt two screws on bottom side of washer with 5/16 nut runner --discard old pump reinstall new one in reverse order --only takes about 20 mins total !!! ---

After unplugging the washer, the unit was pulled forward and tipped backwards, I placed a 2x4 under the washer to serve as a brace. I removed the existing bolts holding the old pump in place, removed the spring hose clams, unplugged the pump and removed the damaged part. inserted the new drain pump, re-inserted the bolts and tightened them, replaced the spring clamps with "regular" hose clamps supplied with the replacement part, plugged in the power supply, removed the brace, pushed back the unit and plugged it into the outlet. From start to finish - about 20 minutes. Was running wash about a half hour after I started.

I was already very familiar with the motor & drain pump, as I had disassembled my original one in attempt to find the problem & fix it. Finally, I broke down & purchased a new one. It was VERY easy to install! The most difficulty was finding the right sized board to put underneath & raise the machine up (with the dryer attached to the top of it) to place the board underneath so that I could tighten the bolts from underneath to attach the pump. After that was over, the rest was cake! Just attach the hoses & the electrical, which just clips in place & my washer is like new again! Yay! Oh, and yes, I'm a woman DIY'er.

Followed instructions from a You Tube video. I'd recently lost my job and money is tight and I thought we could save money doing it myself. By watching the video and ordering parts from you we were able to save $500 between parts and labor. Thanks

This part worked great! Completely fixed all the problems that I had with my washer. A bit hard to actually place it in(pliers are necessary) but otherwise very easy to install.

Thank You so much for the other stories folks wrote on here! We were getting an F21 code on a regular basis. After finding a necklace and about $2.50 in change in the filter tray we found the problem. Over time I thought the washer was getting louder but it was so gradule that we really did not realize it.I had read other posts on here and ordered a new pump. After taking out 3 screws and 2 clamps the pump came right out and went in just as easy. Less than 15 minutes and we were back in business with a wisper quiet washing machine,Thanks Again everyone, Mike D.

I drained the water out of the pump area. Then took off all clamps and holding brackets. Next I pulled off the quick connect power plug. Then I put new pump in the way I took old pump out. The hardest part was unscrewing the bracket from underneath the washer. Cloth washer working fine.

Received water valve in three days, remove top on washer, removed old part and replaced valve with new one, real easy fix, any one could do this. PartSelect confirmed this was the problem and part I needed.

dryer stacked on top of washer. had to lift washer and block w/2 x 4 to get under unit and replace pump

Unplugged washer first! Removed front bottom panel by removing three screws, unscrewed the Drain Plug assembly by turning drain plug counter clockwise with a bucket to catch excess water from washer. Used pliers to remove spring clamps from washer agitator drain hose and then removed the spring clamp from the hose going to drain. Checked hoses for obstructions, then Slide Drain Pump assembly up to the right to remove. Then installed new Drain Pump assembly by sliding pump into slot to the left. Connected the agitator and drain hose to new Drain Pump and fastened with spring clamps. Plugged in AC line cord and turned washer on and started a quick wash cycle to check for leaks and to see if the water drained from washer properly. The water drained from washer and error code did not appear. The error code F21 reappeared during the second wash cycle. After closer inspection with a flash light, I found a large piece of cloth caught between the washer agitator and washer tub covering the drain by shining the flash light up towards the Agitator tub. This was solved by removing the Drain Pump assembly and all of the drain hoses again. Then removing the the large hose from the agitator tub and then removing the large piece of cloth from agitator tub. After reassembly, the washer worked like new!

First unplug the washer and take the back cover off. Loosen the screw on the motor and the big nut on the belt wheel. Take the old belt off and put the new belt on around the motor but slip the motor back in place with the screw slightly in place but do not tighten it yet. Place the belt around the motor and the wheel but this is hard because you need some one with some strength so the is where my dear boyfriend came in handy. He used his strength to stretch the belt and put it back on the machine so I could put the big nut back on. But if you break a wire you have to know a little electrical to put back the wires back in place with small connectors. I do know electrical also. My machine is working better like new. Carol Rozier