LWD27AW (PLWD27AW) Amana Washer - Instructions

Removed lower front cover--two screws. Removed motor/pump assembly after disconnecting electric and water hoses. Seperated pump from motor. Installed belt, then reconnected pump to motor. Reinstalled motor/pump assembly, while rotating belt onto drum pulley. Reinstalled eclectric and water hoses. Buttoned front cover back up. Done.

remove motor and pump togather 4 bolts holding unhook two hose unplug electrial connector and slide out remove 3 screws holding pump to motor be aware of direction belt from moter to tub then place new pump back at same location as old pump replace motor with pump attached back to same location as begfor

Replaced the inlet mixing valve. Two screws and two electrical plug ins and you are done.

Pretty easy repair ... especially after reading previous owners instructions and experiences. After unplugging unit from power and shutting off water supply - 1) Remove front panel. 2) Remove small tensioner spring. 3) Disconnect power connector to motor. 4) Disconnect two water hoses from pump (place towel underneath to catch water). 5) Remove 4 large bolts holding motor assembly to frame. 6) Slide off spin belt from tub pulley. 7) Remove motor assembly. Pump and belt are attached. 8) Take to workbench. Note orientation of belt wrt pump. 9) Loosen and remove 3 star head screws (I used a drill bit and drill). 10) Slide pump off motor shaft. Mine came off clean and easy. 11) Remove belt. It's good to order the belt with the pump and replace them both. My belt was pretty chewed up and I'm glad I had a replacement. 12) Attach new belt and pump, being mindful of belt route. 13) Re-attach motor assembly, threading belt around large pulley. 14) Attach water hoses and motor connector. 15) Attach belt tensioner spring. Test on a short cycle....if all is well, close it up and you're done. Took me about 45 minutes.

knife to losen top, remove rear tabs securing top, unplug electical from timer and switches, unplug front door wiring, 2 bolts remove front, lift front pannel to remove. tape belt on drum on top. under drum you can see the belt around worn pulley. lift idler pulley assembly, remove belt from pulley, snap ring holds pulley in place remove woren pulley, install new, replace snap ring, restring belt. remove tape. spin drum to assure alignment. reassemble.

I read instructions on how to change the pump. I unplugged the washer and then I took off the front panel.I removed the hose clamps and removed the two hoses from the pump.Then I removed the two front springs that hold the drum in place. Be careful because these springs are under tension. I removed the 4 bolts that held the motor to the tub. I unplugged the wires leading to the motor. I removed the motor. I turned the motor upside down and removed the pump and belt. I ordered a belt along with the pump because it was worn. It is best to note how the belt is installed. I took a picture before removing the pump from the motor for future reference if needed. Installation of the new pump and belt was not difficult. I worked the belt around the drum pulley and made sure it turned freely. After completing installation I ran the washer through a short cycle to check for leaks before installing the front cover.

The hardest part was removing the tub from washer by myself. I simply removed the bolts holding the sides to the bottom of the unit and lifted it straight off. Be careful when you remove the springs from the drum so they don't spring back and puncture the drain line. Thank you RTV gasket maker. Once the drum was free from the base, i tilted the drum back exposing the pump housing. I used a pair of pliers to remove both drain lines then removed the 3 hex screws freeing the pump. I had no problem removing it from the motor shaft, it slipped right off. I put everything back together as easily as it came apart.

I read everyone else's stories and tried this for myself. I am by no means a handy person. This was extremely easy and took me about 10 minutes. I would suggest to everyone to try this for themselves if they have the same problem as I did. Anyone can do this.

Took off part and replaced it very easy instructions.

My neighbor did the repair for me and I believe the instructions sent were the reason he had no trouble installing it.

With the right tools this job, should not be that complicated, to me the hardest part was finding the right tools, 1/4 inch small rachet ( the smallest the better,) with a 2 inch extension and a Torx head socket, also known as a 6 lobe,(T25 thats the # that is on the socket) also you need a flat head screw driver,or a 1/4 socket to take the cover off.. and of course the right belt, you might also need a flash light, watch out for spiders, specially black widows, i found a few, First you take the cover off, it should be the easiest part, then, put the rachet,( the smallest the better) with the 2 inch extension and the socket, to take out the water pump, it should be white, it should be only three screws, take your time, when taking out the screws hold them so they don't fall, in to the whasher, it happened to me and it took me a long time to find one of the screws, once you take the 3 screws move the water pump aside it should just drop down from the shaft that drives it, it is not necessary to take the hoses off the pump, put the new belt in place, make sure place it trough the tensioner, there is a guide in the AMANA web site when if you are not so sure, on how the belt goes, once you place the belt, put the water pump back, put the three screws back, put the cover back, run the machine trough a new cycle, Reason why is because i try to run it trough the spin cycle only after i put it together and the belt wouldn't spin, only the motor,Don't forget to unplug the power from the wall before staring all this, I hope this was of some help to you,

a nail from my pocket fell out and was in one of the holes in the in the tub and bound up the tub.when it wold try to spin.ordered the belt and had to order a pump also it melted the bearing in it

Replaced water inlet valve with the water inlet valve kit. We ordered it on Monday morning. The part arrived the next day, Tuesday. New inlet valve was put in on Wednesday. It took less than 15 min., and my washer was working! Very impressed!

Purchased x4 new adjustable legs. Leaned the washer back and held in place with block of wood. Loosened the two older front legs with an adjustable wrench because they had a locking nut and replaced with new legs. Repeated process on back side of washer. Once all the new legs were installed leveled the machine adjusting the legs if necessary.

After pulling front lower panel off, disconnected idler pulley spring and left side tub stabilizer spring to allow room to get motor out the front. Took belt off transmision pulley, unbolted 4 motor mount bolts, dropped the motor/pump assembly down and disconnected the electrical plug (motor). Took motor/pump assembly out, flipped it over, unbolted 3 pump bolts to remove old pump, which came right off. Then reversed the whole process. Pretty straightforward, just time.