LWA90AL (PLWA90AL) Amana Washer - Instructions

Needed part. Ordered Part from PartSelect Friday afternoon and figured I'd get it the following week. No big deal. Part arrived at my doorstep next morning before noon. UNBELIEVABLE SERVICE. Not requested, but it was there. So I fixed the machine as soon as I got it. I wish every company had this kind of service. I've already told my friends. It just can't get any easier than this.

Place black rubber adapter on the end of the drain hose and stick in the stand pipe drain. That's all.

removed hoses from pump, removed 4 screws holding motor housing to washer, disconnected wiring from motor. It will make your life easier to re-assemble if you pay attention to how belt is located in relation to the legs of the pump. pump came off motor very easily. I had the old pump out and the new pump in and working in about 30 minutes.

pull front cover off of machine, disconnect motor wiring harness. Remove 4 sheet metal screws holding motor / pump assembly to frame. Remove both pump hoses (caution - have towels and a bucket at the ready). Pull unit from machine. turn upside down on bench and replace components. Reverse for installation.

Biggest trick is getting the agitator off. It seems like it is bolted on. I used a piece of braided cotton cord to run under both sides of the agitator and just pulled real hard. It WILL pop off.

Next the old seal will also seem to be attached. The edge is firm but not bolted. A small prybar will help.

Easy repair to do, but it did not fix my problem. I decided to get a new washer rather than go through further disassembly.

I had some sweaking and then burning followed. I came to find the belt had burnt and stopped my washer from working. Ordered a belt and replaced. Washer worked for one week. Squeaking and burning again. Belt was still intact, thank goodness. Beleive it is another pulley part for the washer. Might order another part. Overall the fix was good, but had another issue.

First always unplug appliance.Then I shut off the water.I took the front off the washer.Saw the idler was the problem.Ordered parts and new belt.Removed motor assy,and removed pump.Checked impellors and pump bearing.Installed new parts for idler.Installed belt.Re-installed pump to motor,then re-installed entire assy.Turned on water and ecectricity.Ran complete cycle to test.Re-installed front cover.

Disconnect power and water, opened up front end by removing four self-tapping screws, removed the electric motor assembly from frame of machine, replace pump and belt and reassembled.

Removed the damaged legs, replaced with parts from this site and leveled the washer .

Sunday night - removed old valve and hose 15 min went online, found & ordered part - 15 min - part showed up Tuesday afternoon, replaced defective valve 15 min - did laundry! Couldn't have been easier or less expensive!

Unpluged electric, diconnected dicharge hose from wall drain, disconnected water lines from rear of washer and at wall hose connection, removed lower front panel, removed large front panel, disconnected hoses at motor(put towels at hoses to catch water leakage)THEN-took washer to the garage and tuned up side down. Removed front two tub springs, removed (4) motor bolts, removed electrical harness from motor, remove and replaced new brake pads. NOTE:brake pads need to be somewhat driven(pushed hard) into brake pad slots. Also it was easier to install the rear pad by removing the 4" knock-out at the side of the washer. Somehow reinstall the knock-out to keep mice and animals from entering the interior of the washer. THEN- reinstall all items in reverse order. Any one mechaniclly minded can replace the brake pad. My wife and I saved lots by doing the replacement myself. THE END. Good job Gary Final note:besure to intall the drive "v" belt around the 2" pulley wheel.Very important.

I called Lucky Buy when I realized it was more than the drain hose.
I asked if they would install for the same $55 if I got the parts online for less than their price & they said yes.
Once the parts came, they came back (Initial call was $20) for the $55 part replacement call.
At one point he said he had to leave & came back in 20 mins with the pump sawed off (into pieces - it was frozen on the base!)...
He also installed a new belt (Also ordered here for less than their quote!) +
I got braided steel hoses and (3) sets of screens (I'll start changing them annually!) ~
The washer now fills AT LEAST 4x as quickly with new hoses & screens!
The clothing comes out MUCH LESS DAMP with the new belt!
+ it is FAR QUIETER with the new belt!
We're in HEAVEN over here! :-)
ONE THING:
One that first load after the repair, I noticed the water level (Set, as always, to XL) was over halfway UP the side of the agitator's fabric softner dispenser, but thought MAYBE I was "misremembering", but nooo, I don't think I was because LOTS of water spilled out the MIDDLE FRONT BOTTOM once it did the cycle...
(This did not happen when he tested it before leaving - on the SMALL cycle (Which we NEVER use)...
SO!
QUICK FIX:
We set the water level to "LARGE" and all's been fine ever since! :-)
Anyone know whick part we need for the water to stop UNDER the bottom of the fabric softner, like it used to?

I am VERY PLEASED to have found this site and Lucky Buy - I am _SURE_ I saved WAY OVER $100 total (Parts & Labor) & my 15-year old machine is AS GOOD AS NEW NOW (almost - that leak's got to GO! :-)

1) removed front panels from washing machine
2) removed water pump. Three small torque bit screws and (2) hoses.
3) removed motor (because I realized that the belt tensioner also needed work as it was siezed) removed (4) bolts and an electical connector.
4) repaired tensioner by taking apart and cleaning bearing surface. Needed snap ring plyers to take apart.
5) put motor back in
6) replaced belt
7) put water pump back on
8) intalled front panels back on washer

First I tried to lift the lid on the top of the washing machine. I eventually realized this model doesn't open up from the top. I removed two screws on the very bottom of the front panel of the washing machine. Then pulled gently downward to release the front panel from the two clips holding it in at the top. Once the front panle was removed, I found I could easily access the drain hose and disconnect it from the pump by loosening the clamp screw. (Be aware, there is still water in the hose and pump that will run out onto the floor; I had a bucket close by and tried to catch most of this water, but its somewhat futile.) There are two additional hose clips one underneath the tub, and one on the back panel of the washer that hold the hose away from other mechanical parts. Once the hose is freed from those clips it could be removed from the washer by feeding the hose out the back panel. The new hose was then inserted and fed down inside the washer, attached to the pump, tighten the hose clamp screw, clip the hose to the other two clamps so it is out of the way of other parts, reattached the front panel and you're done!

One other note about PartSelect.com...A few days after ordering my part, I had an "International Transaction Fee" show up on my debit card statement. I panicked thinking my card number had been stolen only to call my bank and find out PartSelect is based in Canada.

Removed the motor and mount, removed pump, replaced motor,pump,belt and mount and re-installed. Everything fit and functioned.