This kit is used for front load washers and includes 2 dual-stage shock absorbers, 1 spare shock mounting pin and 4 locking nuts. These shock absorbers keep the washer from vigorous shaking during it's cycles.
This door lock and switch assembly is manufactured to lock the door on your front load washer to prevent it from opening while it is running. You may need to replace the door lock and switch if the do...
The pump is what your washer uses to remove the water from the tub. This part is the pump and motor assembly which includes the red flapper to prevent drain back flow.
Also known as a Door Boot Seal and is used in front load washers. This part is used to keep the clothes inside the tub during the wash cycle. The folds in the bellow allow the tub to move separately f...
This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. T...
This washer shock absorber mounting pin is a small but essential fastener that secures the shock absorber to the outer tub of a front-load washing machine. By holding the shock absorber firmly in plac...
Your washer's door glass panel is the window to efficiency and cleanliness. If it's compromised, it may affect your appliance's performance. That's where our genuine Frigidaire Door Glass Panel comes ...
If your washer isn’t filling correctly, this water inlet valve could be the fix you need. It controls the hot and cold water flow into the tub so your cycles run smoothly and at the right temperature....
$159.57
In Stock
Questions And Answers for LTF2140FS2
Ask our experts a question about this model and we'll get back to you as soon as possible!
5 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Avis
September 16, 2022
Need wire ring goes behind Gasket gasket it has a little crinkles on the wire
For model number LTF2140FS2
Hello Avis, thank you for your question. There are two springs for the gasket. One is the Spring held Bellow Clamp PS1146211 and the other is Door Boot Spring PS975792. We have a video for you to access. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you.
My washing machine will not fill with water. I am not getting voltage to the fill assembly. The pressure switch ohms as good.
For model number LTF2140FS2
Hello Billy, thank you for the question. We believe your washer is having this problem because of the water inlet valve, part number PS2330891, which needs to be replaced. We hope this solves your problem!
The drum is not spinning. The motor never tries to turn
For model number LTF2140FS2
Hi Lyle, thank you for contacting us. Based on our understanding of the issue, we would suggest you checking the drive motor, part number PS2373340, to fix the issue. We hope that helps!
hello both hot and cold water are turned on the machine,but the machine receives only hot water?
For model number LTF2140FS2
Hi Novica, thank you for reaching out. Check the cold water line for any blockage first. If it is fine, the issue could be with the water inlet valve, part number PS2330891. You may need to replace it to fix the issue. We hope this solves your problem!
Hello James, Thank you for the question. We suggest checking the Pressure Hose and Air Chamber. Make sure it is secure and there is no Air Gaps preventing the water from reaching the Pressure Switch. We hope this helps!
This was one of the simpliest repairs I have ever done taking less than 5 minutes to complete. On the inner door I removed the two screws that hold the plastic catch in place. I then removed the broken catch and put the new catch in place. Finally I replaced the two screws that hold the catch in place and it was done.
1. Unplug unit. 2. Unscrew 2 nuts holding top in place in rear of unit using phillips head screwdriver. 3.Slide top back and remove. 4. Open door of washer and unscrew 2 screws holding in door lock unit. 5.Pull out unit from the top and install new unit reconnecting the 3 wire connections.
remove top of machine by removing 3 screws along the top edge in the back of your machine and then sliding the top back and up. Then loosen the screws holding on the control panel enough to get to the 2 screws at the top of the door panel. Next remove bottom panel by removing 2 screws along bottom edge then pulling it free from snaps. Then along the outside lip of the bellow, just inside the door, is a wire clip that is easily removed by prying it past rubber lip with a screw driver and lifting it away. Remove the door panel by removing the 2 screws you exposed by loosening the control panel and 2 more along the bottom that were exposed when removing bottom panel. After the door panel is removed and the bellow is completely exposed, you will find that it is held in place by a circular spring which wraps the whole way around the drum opening. Again it can be removed by prying it out away from the groove in which it sits with a screw driver. Now your machine is broken down as far as it needs to be. From here you can follow the directions included in your new bellow kit and put it back together by following these instructions in reverse.
