Models > LT100AXD1

LT100AXD1 Westinghouse Washer - Overview

Sections of the LT100AXD1

[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Water Inlet Valve – Part Number: 134190200
Water Inlet Valve
★★★★★
★★★★★
(15)
PartSelect #: PS815509
Manufacturer #: 134190200
This washing machine water inlet valve has two ports for water to enter.
$87.48
  In Stock
Order within the next 1 hr and 40 mins and your part ships today!
Light Bulb - Push in and Turn – Part Number: 5308027430
Light Bulb - Push in and Turn
PartSelect #: PS474459
Manufacturer #: 5308027430
This bulb is sold individually. It is used to light up the inside of the dryer once the door is open.
$23.18
  Special Order
BUSHING/FOOT KIT – Part Number: 5303937190
BUSHING/FOOT KIT
PartSelect #: PS1156911
Manufacturer #: 5303937190
$75.04
  Special Order
6
6'X3/8" Stainless Steel WASHER F
PartSelect #: PS2343260
Manufacturer #: 5308816562
$28.19
  In Stock
Order within the next 1 hr and 40 mins and your part ships today!
GASKET – Part Number: 5303261021
GASKET
PartSelect #: PS457585
Manufacturer #: 5303261021
$96.22
  Special Order
BOOT – Part Number: 5303261132
BOOT
PartSelect #: PS457594
Manufacturer #: 5303261132
  No Longer Available
V-Style Belt – Part Number: 5303261151
V-Style Belt
PartSelect #: PS457598
Manufacturer #: 5303261151
This v-shaped idler pulley belt is for washing machines that use three belts and that are loaded in the front. Made by Frigidaire, this belt is 46-5/8 inches long and 1/2 an inch wide. Use it for your...
  No Longer Available
V-Style Belt – Part Number: 5303261153
V-Style Belt
PartSelect #: PS457599
Manufacturer #: 5303261153
This v-shaped high speed spin belt is for washing machines that use three belts and that are loaded in the front. Made by Frigidaire, this belt is 53-3/8 inches long and 1/2 an inch wide. Use it for y...
$30.10
  Special Order
V-Style Belt (Drive) – Part Number: 5303261155
V-Style Belt (Drive)
PartSelect #: PS457600
Manufacturer #: 5303261155
This v-shaped drive belt is for washing machines that use three belts and that are loaded in the front. Made by Frigidaire, this belt is 41-1/2 inches long and 3/8 of an inch wide. Use it for your Fri...
$24.01
  Special Order
PAD – Part Number: 5304464978
PAD
PartSelect #: PS2333729
Manufacturer #: 5304464978
$60.25
  In Stock
Order within the next 1 hr and 40 mins and your part ships today!
Stainless Steel FILLHOSES C6 2PA – Part Number: 5304490736
Stainless Steel FILLHOSES C6 2PA
PartSelect #: PS8760368
Manufacturer #: 5304490736
$65.80
  Special Order
SPRING – Part Number: 5300011943
SPRING
PartSelect #: PS450031
Manufacturer #: 5300011943
  No Longer Available

Questions And Answers for LT100AXD1

Be the first to ask our experts a question about this model!

Common Symptoms of the LT100AXD1

[Viewing 2 of 2]
Leaking
Fixed by
these parts
Fixing
Show All
No hot or cold water
Fixed by
these parts
Fixing
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Washer Continued To Fill To Point Of Overflow
First I removed the top panel held by four screws at rear of panel, pulling the panel foward and up. Then disconnected the power and water connections. Then I removed the two screws holding the flow valve to the washer rear panel,pulled the valve foward ,removed the two electric connectors, pinched the water clamp with pliers and removed the water connection to the valve. Then replaced with the new valve followed the above steps in reverse order, finishing up by re placing the water connections and power. Then checked fo proper replacenent and leaks before replacing top panel.
Parts Used:
Water Inlet Valve
  • alvaro from east hampton, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
86 of 96 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No Cold Water
Checked problem on-line and discovered it was the water inlet valve. Matched the part on part select. Com. Finding the part was very easy. Part select had a grid behind the picture to help determine the size and pictures from all sides. Removing the old part, matching it, and replacement took a total of 30 minutes. I now have clean clothes.
Parts Used:
Water Inlet Valve
  • Mark from Pittsburgh, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
16 of 18 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water continued to flow into machine during spin cycle
After moving machine to an area that allowed easy access to the unit, disconnected the water supply hoses from the inlet valve.
Removed the two screws that keep the back in place, removed the clips that keep the top in place, moved the top over far enough to get the valve out. Removed the screw that keeps the inlet valve in place, disconnected the power supply to the valve, Pulled valve out in order to remove the water outlet hose. Repalced with new vale, and reversed order to install. Works just fine now.
Parts Used:
Water Inlet Valve
  • Howard from Lcolnton, GA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
16 of 18 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!