The tumbler and motor belt in your dryer allows the drum to spin during the drying cycle. At 100 inches in length, this dryer drum belt is 3/8 of an inch wide and has five ridges. The belt is black in...
This front glide kit comes with a blue plastic glide, a brown cork pad, and two metallic rivets. Two kits are required per appliance. A rivet tool is required for this installation.
This lint filter screen is slide in styl type of Maytag filter screen. It is most typically used for the 08 and later series of Maytag gas or electric clothes dryers that appear before 1990.
This kit comes with hub assembly, agitator seal and spanner nut. If your washer leaks once full (with or without clothes in it) or leaks during agitation, then you should replace the seal.
This part is used to help the belt to rotate the drum. It is white and made of plastic with a metallic bearing in the center.
$24.56
In Stock
Questions And Answers for LSE7806ACE
Ask our experts a question about this model and we'll get back to you as soon as possible!
10 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Pamela
December 28, 2019
My Maytag washer's agitator won't work but the rest does
For model number LSE7806ACE
Hi Pamela, you may wish to try inspecting/replacing the belts with belt kit PS2005284. Thank you for your question and good luck with your repair!
Where does part number PS2032222 hookup? On both ends?
For model number LSE7806ACE
Hi Patty,
Thank you for your question. This spring would attach to the idler pulley arm on one end and the motor mount on the other end. We hope this helps. Thank you and have a great day.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Gerie
November 24, 2021
Washing machine will fill with water only if the dryer is running. Why is this and what needs to be fixed.
For model number LSE7806ACE
Hi Gerie,
Thank you for your question. If the washer will only fill with water when the dryer is running, there may be an issue with either the washer lid switch or the electronic control board. You will find information on how to test these parts under Free Repair Help and Instant Repairman on our website. We hope this helps! Good luck with the repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Pauline
January 25, 2020
Washer does not empty totally after wash and rinse cycles. Need to spin a second time for it to drain all water.
For model number LSE7806ACE
Hi Pauline. Check the drain hose PS11739309 and pump hose PS11738880 for clogs it could also be a faulty drain pump part number PS11743017. Thank you for your question and good luck with your repair.
Was this helpful?
Thank you for voting!
John
October 11, 2021
Where are fuses on unit ?
For model number LSE7806ACE
Hello John, Thank you for the question. There is a thermal fuse is mounted on the heating element and the Blower Housing housing. We hope this helps!
Removed the front cover (screws on bottom 0f face)...removed blower cover....spring pliers to remove and install blower fan. the rest of the time was spent cleaning the inside of the shell as well as the vent. Reassembled and dryer runs better than it has for many years.
Unplugged dryer. Front came off easily. Removed front of blower. Wheel came off fairly easily - could then see that shaft of motor was circular with flattened side but inside of old wheel was rounded. New wheel popped right on. Took tumbler off so I could clean lint out more easily and get a good view of how the belt threaded through. Put the tumbler back on and reached back with both hands to thread it. Took a half dozen tries until I was sure it was seated correctly and not twisted. Put front... of dryer back on. So far (a week or so) the rumble is gone. Seems blower wheel was the cause of the rumble. Belt didn't seem worn but replaced anyhow.
I removed the 2 phillips screws on the bottom of the front panel. Then checked around to find the belts were actually below the floor panel. I pulled the washing machine away from the wall and tilted it bacwards and found the pump belt was off the pully and the drive belt was badly damaged. I replaced the 2 belts which took no tools and about 3 minutes to accomplish then resecured the front panel, pushed back in place and leveled. Complete repair from diagnosis to back in operation took less than 15 minutes.
