This temperature sensor, also referred to as a thermistor, is a genuine replacement component compatible with various appliance models. It works in coordination with the control board to monitor inter...
$59.35
In Stock
Order within the next 4 hrs and your part ships today!
This gas range oven igniter is compatible with various models of LG gas ranges. It is made up of the igniter element, wire harness, connector and mounting bracket. The igniter is responsible for gener...
$317.43
In Stock
Order within the next 4 hrs and your part ships today!
If your cooktop grates are cracked or wobbly, this replacement grille can help. It gives your pots and pans a stable surface and protects the burners underneath. It’s built tough to handle heat and ev...
$204.98
On Order
Questions And Answers for LRGL5823S
Ask our experts a question about this model and we'll get back to you as soon as possible!
5 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Melissa
July 7, 2023
I need the conversion kit to trasnsfer the stove from gas to propane can I order this here
For model number LRGL5823S
Hi Melissa, thank you for getting in touch. The LP conversion kit compatible with your model is part number PS16222236. We hope that helps!
looking for an extra oven rack and can't seem to locate one on this site
For model number LRGL5823S
Hi Christine, thank you for the question. The part you are looking for is the oven rack, part number PS16224466. If you need help placing an order, customer service is open 7 days a week!
Hi, The serial Number for my stove is as follows 107MMXN0C026
Model# LRGL5823S /01
I'm looking for controller board and the corresponding LG Range PCB Display Assembly controller circuit board for this model.
Any help would be appreciated.
Thank you for your attention.
Jose.
For model number LRGL5823S
Hi Jose, thank you for your question! The main control board is part number PS16223749. The display control board is part number PS16223754. We hope that helps!
My gas range continues to give an F3 code and won’t start. What is the most likely cause? By the way, I’ve done all of the recommended troubleshooting steps except for putting it on the curb for the landfill.
For model number LRGL5823S
Hello Stewart, thank you for your inquiry. The error code F3 indicates a touch pad sensor key error. We would recommend checking the control board, part number PS16223046, to solve the issue. We hope this helps!
Go onto youtube, such as https://www.youtube.com/watch?v=-ITkrwhDNMQ and watch similar videos for DYI. The process is very similar to other models.
Once the door is removed, place oven door on a towel or soft place so it does not scratch the door. Unscrew the screws and make sure you notice where each screw goes, so you know the process of where each screw goes when you re-assemble.
Once the inner cover is removed, remove the insulation, too so you don't damage it. Use Wet/Dry Shop Vac to clean the shattered glass. (WORD OF ADVICE: I did not remove the insulation and the suction of the Shop Vac removed part of the insulation, so now instead of a quick turn around repair turns into a few weeks repair, because the insulation is on back order 10-14 days from the supplier. DON"T MAKE THE SAME MISTAKE!)
Once the glass has been removed, the new inner glass is replaced, begin by re-assemble the oven door with the correct screws and attached the oven door to the range.
This is a gas stove with 110v electric. Unplug cord before beginning.
Remove back cover. There Phillip approx 15 Phillips screws. Back cover slides up off of tabs to remove .
You need to get the main board out of the way to get to the Display PCBA. There were three wiring harness connectors on the right side of the board you need to disconnect which allows the Board to slide out to the right. Use plastic pry bar to pop tabs slightly on top and right side of board that will allow you to slide the board out to the right. You need to take care to not break these tabs.
I did not disconnect the other wiring harnesses on left side of board. I lifted the board and laid it out of the way on the top of the back of stove. I held it in place with a piece of duct tape holding it to top by wiring harness to give me room.
Now you have access to the Display PCBA. This board is held in place by 5 screws. Remove screws and place new board in place with the 5 screws.
Now put the main board back in place by sliding in place from right to left and under the tabs on all sides. This is a little tricky but with a plastic pry bar and going slowly not to difficult. Be careful not to pinch wires behind the main board. There are relief openings that wiring should be routed through.
Plug the cord back in and make sure all is working on the Display and push buttons on front pad.
Finally place the back cover on and secure with screws.
Took off the oven door then took out the racks and two screws in the oven bottom and removed it . Then removed the heat deflector. Then un plugged the old igniter and removed the burner to make it easier to remove the old igniter. Then installed the new igniter and reversed the process
