This temperature sensor, also referred to as a thermistor, is a genuine replacement component compatible with various appliance models. It works in coordination with the control board to monitor inter...
This clear inner glass lets you see inside your LG oven while keeping the heat in. If your oven glass is cracked or chipped, replacing it helps restore energy efficiency and safe cooking. It’s made to...
A dual radiant heater supplies heat to a cooking area beneath a glass cooktop. Replacement may be needed when one zone does not warm, only the inner or outer section works, or the element has a visibl...
This genuine heating element fits select LG ovens and ranges, providing heat for broiling and baking. Located at the top of the oven, it ensures even cooking and reliable performance. It replaces olde...
This sheathed heater provides controlled heat for appliance operation while protecting internal components. Its protective casing supports durability and consistent heating performance.
Ask our experts a question about this model and we'll get back to you as soon as possible!
5 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Gregg
December 26, 2019
I set the oven temp to 350 degrees, but it only heats too 325 or so. Adjusted the thermostat up 30 degrees but didn't make that much of a difference. What's could be causing this issue? Thanks in advance!
For model number LRE3083ST
Hello Gregg, Thank you for the question. I suggest testing the Temperature Sensor, PartSelect Number PS6883927. Testing the temperature sensor probe on your oven is easy. With the sensor at room temperature, measure the resistance between the two prongs at the end of the sensor connector. The resistance of the sensor should read approximately 1080 – 1090 ohms at room temperature. Hope this helps!
I have an LG electric oven that wil not get to the proper temperature when set , I have replaced the temperature probe INSIDE the oven ,, it did not fix the problem ,, is there another thermostat somewhere that controls temperature in OVEN ?? thank you
For model number LRE3083ST
Hi Ken, thank you for reaching out. We have researched and found that the issue is with the control board, part number PS11773404. It monitors the temperature and controls the oven heat. We would recommend replacing the control board to fix the issue. Glad to be of assistance!
Hello and thank you for writing.
It certainly sounds like it could be a faulty element (left front)PS7795472 and/or element PS7795471 (right front) and /or element PS7795470 (right back )you should check the part(s) for signs of damage or test with a multimeter, and replace the part(s) as needed. We hope this helps. Please contact us anytime if you require further assistance.
Oven not heating, warming zone on glass top not heating, changed the temp sensor and the thermal fuse, not heating still. What's next?
For model number LRE3083ST
Hello Dave, Thank you for the question. Normally this is an indication the Main PCB Board is defective and may need to be replaced. We hope this helps!
Hello Sharlene, thank you for your question. We have researched your model and found that the issue is probably with the Surface Element. Your model comes with two surface elements on the front side: the right surface element, part number PS7795472, and the left surface element, part number PS7795471. If that does not take care of the issue, then the problem is most likely to be related to the main control board, part number PS11773404. If you require assistance to place an order, please contact customer service. We hope that helps!
Dropped a hammer on the range while removing a ceiling light. Viewed a How-To video on Google. Ordered the needed parts. Followed the steps from the How-To video. Reinstall was a bit tricky by myself - could have used an extra set of hands. I have a few words of caution: 1) Put something between the range top and range - like a sheet or drop cloth - to prevent a dropped screw from falling into a crevice in the stove. I dropped a screw and was unable to retrieve it, even with a magnet. 2) Makes sure you remove all bumpers, screws, clips, etc. from the item being replaced and put them on the new item if the new item does not come with replacement bumpers, screws, etc.
1. Unplug the stove (you will need 1 person to assist). 2. Remove the 3 assembly screw (Philips screws) located underneath the front of the assembly, near the oven door. 3. Raise the plate assembly to expose the heating elements (Take a photo of the positioning for installation reference). 4. Remove the wires connected the heating elements (unclip the connectors only). 5. Remove the holding clips from the heating elements (2 clips on each elements, the large element has 1 clip and 1 screw). 6. Remove the elements only (leave the wires in place). 7. Remove the Plate Assemble (save the 2 black rubber mounts located on the sides, the new assembly dose not come with replacements) . 8. Now your are ready to reinstall the Plate Assembly, so do the reverse and you should have no issues (check your photo for proper installation).
Checked element no reading. Took off back panel and removed element. Took 5 days to get element. Put in new one. Took 20 minutes. Did not have to cut panel as video had shown. It had screws and was easy to get out and put the new one in. The new element was exactly the same as the old one. I checked all elements before ordering. Was satisfied with everything but the delivery time
