This temperature sensor, also referred to as a thermistor, is a genuine replacement component compatible with various appliance models. It works in coordination with the control board to monitor inter...
This clear inner glass lets you see inside your LG oven while keeping the heat in. If your oven glass is cracked or chipped, replacing it helps restore energy efficiency and safe cooking. It’s made to...
Is your LG range oven stove not heating quite like it used to? The Radiant Surface Element could be just what you need. This genuine LG part is specifically designed to provide heat directly to your r...
This genuine heating element fits select LG ovens and ranges, providing heat for broiling and baking. Located at the top of the oven, it ensures even cooking and reliable performance. It replaces olde...
We know you love your LG range oven, and when it's not performing optimally, it can be frustrating. Don't worry, our genuine OEM relay control board PCB assembly is here to help. Designed especially f...
Don't let a faulty heater ruin your meal prep plans! Improve your cooking experience with this high-quality Radiation Heater from LG. This particular part is a critical component of certain LG range m...
This sheathed heater provides controlled heat for appliance operation while protecting internal components. Its protective casing supports durability and consistent heating performance.
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Glen
November 18, 2023
Get a F-9 code. Should I change the thermostat or the relay board? Or both ? My wife did use the oven clean and it only worked a couple times after that. Thanks Glen
For model number LRE3083ST
Hello Glen, thank you for the question. An F9 error code on an oven means that the oven has failed to exceed 150 degrees Fahrenheit after five minutes of preheating. Sometimes, the F9 error code is the result of an electrical fault that has magnetized the circuitry. Resetting the oven by disconnecting the power for five minutes will demagnetize the circuitry and resolve the F9 error. Check wiring from sensor to board. If good, check the temperature sensor, part number PS11732697, using a multimeter. If it is fine, then you will need to replace the relay control board, part number PS8751324. We hope this helps.
Hello Kevin, thank you for getting in touch. If the left front surface element of your model is not heating, then we would recommend checking the display control board, part number PS7792510, to solve the problem. A malfunctioning display control board can most probably cause this issue. We hope this helps!
Dropped a hammer on the range while removing a ceiling light. Viewed a How-To video on Google. Ordered the needed parts. Followed the steps from the How-To video. Reinstall was a bit tricky by myself - could have used an extra set of hands. I have a few words of caution: 1) Put something between the range top and range - like a sheet or drop cloth - to prevent a dropped screw from falling into a crevice in the stove. I dropped a screw and was unable to retrieve it, even with a magnet. 2) Makes sure you remove all bumpers, screws, clips, etc. from the item being replaced and put them on the new item if the new item does not come with replacement bumpers, screws, etc.
1. Unplug the stove (you will need 1 person to assist). 2. Remove the 3 assembly screw (Philips screws) located underneath the front of the assembly, near the oven door. 3. Raise the plate assembly to expose the heating elements (Take a photo of the positioning for installation reference). 4. Remove the wires connected the heating elements (unclip the connectors only). 5. Remove the holding clips from the heating elements (2 clips on each elements, the large element has 1 clip and 1 screw). 6. Remove the elements only (leave the wires in place). 7. Remove the Plate Assemble (save the 2 black rubber mounts located on the sides, the new assembly dose not come with replacements) . 8. Now your are ready to reinstall the Plate Assembly, so do the reverse and you should have no issues (check your photo for proper installation).
Checked element no reading. Took off back panel and removed element. Took 5 days to get element. Put in new one. Took 20 minutes. Did not have to cut panel as video had shown. It had screws and was easy to get out and put the new one in. The new element was exactly the same as the old one. I checked all elements before ordering. Was satisfied with everything but the delivery time
