This temperature sensor, also referred to as a thermistor, is a genuine replacement component compatible with various appliance models. It works in coordination with the control board to monitor inter...
$59.35
In Stock
Order within the next 7 hrs and your part ships today!
This clear inner glass lets you see inside your LG oven while keeping the heat in. If your oven glass is cracked or chipped, replacing it helps restore energy efficiency and safe cooking. It’s made to...
$125.28
In Stock
Order within the next 7 hrs and your part ships today!
This genuine heating element fits select LG ovens and ranges, providing heat for broiling and baking. Located at the top of the oven, it ensures even cooking and reliable performance. It replaces olde...
$142.24
In Stock
Order within the next 7 hrs and your part ships today!
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
John
December 26, 2019
Oven has a heat disparity of 50 degrees between manuel thermometers and the oven temperature reading. Adjusting manually via the instruction book only adjusts 9 degrees at a time. Temp is on at 350. If you turn the temp to higher the temp actually decreases. The convection fan operates.
For model number LRE3023ST
Hi John, sounds like a faulty temp sensor in the oven, I would recommend replacing it. Thank you for your question and good luck with your repair!
My oven model # lre3023st front 8" burner was ordered and replaced. But it still is not working properly. It eventually glows on for 6 to 7 seconds as it should, but may not re-energize for another 5 to 10 minutes. Is my problem the infinite burner switch? And if so what part number should I order? Also, are there two switches (one for each 8" front burner?) appreciated and thank you
Hello Oscar, Thank you for the question. If the element did not fix the issue, it is normally a defective switch. I have researched the model you have provided and have found the part you are looking for is PartSelect Number PS7792509. We hope this helps.
Both large front burners wont turn on, can hear relays "click" no heat. Suggestions?
For model number LRE3023ST
Hello David,
Thank you for your question. Our sources suggest replacing the electronic control board under part PS8751313 for your model to fix your issue. Hope this helps!
Dropped a hammer on the range while removing a ceiling light. Viewed a How-To video on Google. Ordered the needed parts. Followed the steps from the How-To video. Reinstall was a bit tricky by myself - could have used an extra set of hands. I have a few words of caution: 1) Put something between the range top and range - like a sheet or drop cloth - to prevent a dropped screw from falling into a crevice in the stove. I dropped a screw and was unable to retrieve it, even with a magnet. 2) Makes sure you remove all bumpers, screws, clips, etc. from the item being replaced and put them on the new item if the new item does not come with replacement bumpers, screws, etc.
1. Unplug the stove (you will need 1 person to assist). 2. Remove the 3 assembly screw (Philips screws) located underneath the front of the assembly, near the oven door. 3. Raise the plate assembly to expose the heating elements (Take a photo of the positioning for installation reference). 4. Remove the wires connected the heating elements (unclip the connectors only). 5. Remove the holding clips from the heating elements (2 clips on each elements, the large element has 1 clip and 1 screw). 6. Remove the elements only (leave the wires in place). 7. Remove the Plate Assemble (save the 2 black rubber mounts located on the sides, the new assembly dose not come with replacements) . 8. Now your are ready to reinstall the Plate Assembly, so do the reverse and you should have no issues (check your photo for proper installation).
The repair person could not complete the job as the part sent is totally wrong for the appliance. The company has not responded to me email sent 12/30/23 and there is no way to leave a voice mail or ask for a call back, due to large call volume. A live representative does not answer the phone.
Please check your emails. You ask for feedback on repair, but obviously do not take time to check emails for issues. Because the error is on the part of PartSelect I requested an RMA to return an incorrect part. Please respond by sending a shipping label so it can be returned for a refund. I have submitted a dispute with the credit card company since your company is negligent in customer service. Please email RMA shipping label to [email protected]
