LEV4634PQ0 Whirlpool Dryer - Instructions

Lint screen on my 30-year dryer was torn. Ordered the new screen here with just the part number, fits well. Very helpful website.

PartSelect sent me three different door catches with instructions for choosing the correct one. I did choose and simply inserted it into the slot and voile! All finished and it works great now! PartSelect had the part delivered the day after my order was placed. I would suggest doing business with them to anyone asking who they might contact for a part. I especially appreciated the ease of identifying and ordering from them. I was able to do all of this on-line via their website.

Found one of the two drum support rollers was badly worn. Found Partselect.com, found my parts in less then 2 mins. Figured that I was in there so I should just replace the belt so I got one of those also. Parts arrived in 3 days dryer as good as new in 20 mins.

Used the YouTube video sent by this site

I opened up the dryer as per the instructions I had received from PartSelect tech support. It was very easy to do. The only unexpected thing was that the original belt had snapped and in doing so the idler pulley was actually laying on the floor of the dryer's bottom. I had to figure out how it went, but that only took a minute and I popped it back into place. I held the drum by hand while pulling the dryer face away so it wouldn't fall and then I slipped the belt over the drum and quickly closed the front up again. I aligned the belt on the spot where the old one had been, pulled it through the idler pulley and over the motor and voila. Done. I closed up the dryer and was on to another "Honey Do" project within 20 minutes.

First I raised the top of the dryer(after unplugging the power cord) disconnected two wires to the front door switch and then removed two screws using a nutdriver. The front cover lifts up and while supporting the drum set the cover aside. Slide the belt off the drum and remove it. I then removed the two support roller tri rings and replaced the rollers and tri rings and reassymbled the dryer.
It was a very simple repair.

Thanks Mike

I lifted the top of the dryer cabinet, like the hood of a car using a screwdriver to pry it open. I removed the two screws in the upper right corner of the cabinet front. I disconnected the safty switch on the front door. The front of the cabinet can then be removed by lifting up the front off the pins in the base. With the drum exposed you can place the belt on and thread it through the two pulleys on the motor. Consult the diagrams provided on the PartsSelect website for the proper positioning of the belt on the pulleys. After the belt is installed spin the drum by hand one turn to make sure that it is seated properly on the drum and pulleys. Reassemble the dryer in the reverve order.

Removed the two screws under the lint trap
Opened the top (had to use flathead screwdriver to release latches)
Disconnected door switch harness from front panel
Removed 2 screws holding front panel on dryer
Lifted out dryer drum (previous belt had broken)
Vacuumed inside of dryer (found $3 in quarters!)
Put new belt around drum
Put drum back in dryer, using empty laundry soap bottle to support its weight
Looped belt around pulley and motor; secured pulley to dryer bottom
Made sure rear gasket thingy was aligned properly and drum turned freely
Put front panel back on
Re-attached door switch
Closed top and put screws back in under lint trap
Fired it up - WOOHOO!

I used a screwdriver to remove the old part and pushed the new part in with my fingers, it was very easy. If I could do it, anyone can. I was a lot cheaper then having a repair man come to house. I am very glad I found your site online, I will definitely be using your company again.

I watched the video on how to diagnose problem and then how to repair . Videos were very helpful. Also the parts were ordered on line and arrived in 2 days. Parts at a local appliance parts store were twice the cost of what I paid for the parts from PartSelect.

I raised the top of the dryer, removed the front, the belt and the drum. Slipped off old rollers, installed new ones and new tensioner. Reinstalled drum and belt, bolted front back on and closed the top.

I lifted the top of the dryer and removed the front panel. I removed the drum exposing the drum rollers. I replaced the rollers and reassembled the dryer. The exploded views on the web site made it easy to see what to do.

first we printed out directions from a couple of online repair sites that had pictures.
We followed the directions to remove the front of the dryer and removed the belt off the drier and then took out the drum. We had a hard time trying to keep the rear seal on so used CLOTHES PINS to put on the seal, then we added the adhesive replacing the clothes pins until the whole seal glued. Since the drum was already out, we put it in the sun to really dry the glue.
Next we attacked the drum support rollers. We removed the back of the dryer and used a 9/16" socket with an extention to remove the back nuts.
We took out the shaft, used sandpaper on it and then replaced the triangle clips and the support rollers.
Then put the back on again, then the front, making
sure the drum fit on the front. You have to then figure out the belt, with the rubber side down, and then work with the tensioner, which took my poor husband a while. Then lowered the top, put the clips back on and the bottom, making sure we turned the drum. It was a success after about 3 hours. You can do it a lot easier with pictures.

The dryer quit working. I did some trouble shooting on your amazing site, ordered what i thought it might need and then got to work. Took no time to get it apart and replace roller kit and belt. What took the longest was getting in there and cleaning out probably 15 years worth of dirt and dust. If you have not opened your dryer up and done this, 10/10 recommend, because in doing so i found that the motor was the real culprit. Once i opened it up more, especially cleaning around the blower fan and motor, i was half a day in. Put it all back together and got it running for two more loads before the motor quit. Replaced that and since the hard work was done, had it back in in half an hour and running great. Probably will need to redo the felt seal one day, but for now, i am calling it a win. This is my go to site for all things and i have been able to work on most of my major appliances and do it myself using the helpful information here.

pressed clip into hole on top of front panel. first remove two philip screws that hold filter so you can lift top up.