This kit comes with hub assembly, agitator seal and spanner nut. If your washer leaks once full (with or without clothes in it) or leaks during agitation, then you should replace the seal.
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
$26.51
In Stock
Order within the next 6 hrs and your part ships today!
This washing machine drain pump is intended for use with automatic washers that have been manufactured since 1958. The pump itself is made of plastic, though it does come with a metallic belt pulley.
$255.89
In Stock
Order within the next 6 hrs and your part ships today!
This damper pad kit is used for base support. It comes with three six inch damper pads, two little tubes of lubricant. NOTE: This part will need adhesive to stick it in place.
$57.69
In Stock
Order within the next 6 hrs and your part ships today!
This black lid switch assembly comes complete with a bracket, two switches, and a fuse. An open fuse might indicate that the lid switch is bad. The point of the lid switch is for the tub to stop spin...
$54.09
In Stock
Order within the next 6 hrs and your part ships today!
This hose clamp extends from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag brand washing machines.
$11.68
In Stock
Order within the next 6 hrs and your part ships today!
This is a heat-resistant adhesive for your appliance. The heat resistance allows you to stick parts such as grate feet, gaskets, and felt seals in hot areas, such as a cooktop, without compromising th...
$30.41
In Stock
Order within the next 6 hrs and your part ships today!
This foot pad is just over an inch in diameter. It is made entirely of rubber and is gray in color. This pad is intended for use with washers and some dryers.
$19.48
In Stock
Order within the next 6 hrs and your part ships today!
Questions And Answers for LAT9304AAE
Ask our experts a question about this model and we'll get back to you as soon as possible!
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Brian
July 30, 2023
Washer will spin and drain but won’t fill. Is this a failed valve?
For model number LAT9304AAE
Hello Brian, thank you for your inquiry. The issue is most likely with the water inlet valve. The water inlet valve opens to allow water to enter the washing machine. If the water inlet valve is defective, the wash may not fill at all. The water inlet valve requires sufficient water pressure to function properly. First, check the water pressure to determine that it is adequate. If the water pressure is adequate, try cleaning the screens inside the water inlet valve hose connection ports. If the washer still does not fill, replace the water inlet valve, part number PS11739275. We hope this helps, good luck with this repair!
Hello Tony, unfortunately we do not have instructions for that exact part number but we did find a video that may help for a similar model: https://www.youtube.com/watch?v=9KNJwyWZqFc
Was this helpful?
Thank you for voting!
May
January 21, 2020
Replaced lid switch, belts, and tub bearing now the motor is smoking. Do i need a motor switch
For model number LAT9304AAE
Hello May, thank you for your question. Yes, it sounds like the motor start switch has failed. The switch is discontinued, so you would have to replace the entire motor, which is PartSelect Number: PS2003768.Please enter the part number into the site for current price and availability. Good luck with your repair!
Was this helpful?
Thank you for voting!
Walter
February 18, 2020
When spinning out the drain water goes from the pump up the hose to a small valve body mounted on the back wall of the washer. There is a rubber valve in here that is allowing water out and dripping on to the floor. Can you help me with info to fix this please.
For model number LAT9304AAE
Hello and thank you for writing.
It certainly sounds like it could be a damaged pump to siphon drain hose PS11739284 you should check the part(s) for signs of damage and replace the part(s) as needed. We hope this helps. Please contact us anytime if you require further assistance.
I removed the 2 phillips screws on the bottom of the front panel. Then checked around to find the belts were actually below the floor panel. I pulled the washing machine away from the wall and tilted it bacwards and found the pump belt was off the pully and the drive belt was badly damaged. I replaced the 2 belts which took no tools and about 3 minutes to accomplish then resecured the front panel, pushed back in place and leveled. Complete repair from diagnosis to back in operation took less than 15 minutes.
My washer is 5 years old and water began to leak on the floor. I took off the front panel and filled the tub. Water did not leak immediately, but after the tub filled with about 3-4 inches of water, the water began to leak from a rubber washer between the fixed tub and the drive shaft. I looked online for exploded diagrams of Maytag washers, when I came across your site. By looking at your diagrams, I determined what parts I needed and ordered them. The parts arrived in 2 days, and I installed them. There were no leaks and it cost me under $70 (a repairman would have cost at least $250). The only thing I would recommend to those in similar situations, is to purchase a spanner wrench (your site does not sell, but others do). The stem seal and hub assembly is reverse threaded (clockwise to loosen) and is difficult to remove due to tight quarters in the tub.
Well, I found the washer leaking water from the bottom a couple weeks ago. I finally got around to pulling off the front panel and ran a couple cycles to see where the water was coming from. Turns out the leak was at the plastic pump that does the draining after wash and rinse.
So I got the model number and googled online. I found Partselect and they had every part I needed. Took me 10 minutes online to find the parts for my specific washer. I couldn't believe how easy it was. Parts came in two days...and this was right before Xmas.
Anyways, changing out the pump was simple. Took 5 minutes to get it off and put the new one in. I decided to change the hoses and elbow siphon break as well while I had the thing apart as those parts were old...but still working well.
Got the washer back together and the floor is dry as a bone. Perfect repair, really easy to do. Hardest part was figuring out how to get the front panel off.