KUDC24SESS24 KitchenAid Dishwasher - Instructions

Removed the old mount from the upper rack. Removed the broken stem from the old mount that was attached to the arm. Attached the new mount to the spray arm. Attached the mount and arm to the rack.

At first I considered replacing the gasket on my own but was not sure If that was the problem. I had a service person come in (at great expense) to tell me it may or may not be the problem but he could order the gasket and replace it. I did it myself.

I removed the old gasket by hand, simply by pulling it out of its track. I sprayed clean water in the track to clean out old soap and debris. I soaked the new part in warm water for a few minutes to soften and lubricate it. I centered the gasket in position and began pushing it into the track with a one inch putty knife, being careful not to damage the rubber. There is a slot along the gasket that will accept a flat tool to push it in. At the corners, I had to use a screwdriver to work around the curves. In a few minutes the gasket was in and no more leaks. It couldn't be easier.

just pay attention to how the old gasket was installed, then pay close attention to how you remove it from its groove. replace with flat sides and grooves just the same.. I actually left about on third of the old gasket in place until I seated the new gasket to make sure I was doing it correctly. visually divide the gasket groove into 2 parts with the dividing line at the top of the groove, place a piece of tape on the new gasket at its middle and begin there, first one side then the other,,, that way there is no stretching to complete the circuit. easy , I am a 62 year old grandmother of 7,,,,,,,,,,,,,,,,,,,,,,,,,,,

I simply had to hook up the power cord to the dishwasher so i could plug it into the outlet rather than direct wire the appliance. Everything went very smoothly. Everything needed for installation other than tools was provided. Easy to follow instructions if you know a little about electrical wiring.

Hey parts select, I'm Julia's husband and the repair was a simple remove and replace. Only one screw to hold the manifold together and the mounting hardware that we had to order separately was a snap in piece which was different form the original but went in just fine. You saved me from having to buy a new dishwasher which Julia was more than happy to go shopping for!! Thanks!!

Removed 2 screws that held the old mount and washer arm in place, new mount was very easy to install, it snapped in, only one screw needed, remounted the washer arm and the job was done. I was really impressed with the ease of ordering and how quick it got here (3 days), also the scematics you have online are very helpful. I printed them out since I don't have the owners manual any longer, they're very helpful in matching up and ordering the right part which saves a lot of time, also I like the way you can just search by model number and appliance name to find the right parts, makes the entire process really easy. I know I will continue to shop here when the need arises. It really cuts down on expensive repair costs.

I had replaced the control board a month or two earlier. Then smelled plastic burning. I noticed the Sta-con connecters in the molex plug had burned - that's what took out the control board. The fuse assembly came with new connectors - so you know this is a known problem with the machine. If you're handy you can buy the thermal fuse from Newark for $0.88 and replace it by soldering - but you need to replace the sta-cons. They corrode and the bad connection causes the heat making the thermal trip.

DEFINITELY 5***** Stars
The piece arrived, and my husband was able to pop out the old flexrow and pop in the new one.....took less than one minute. Voila...back in business again.

We had just made the (big) decision to not renew the warranty. The dish washer is 10 1/2 years old, and we figured we'd cross our fingers...never having a problem with it. A week later the flexrow broke. I called KitchenAide...they would/could send an entire bottom rack for $135.00. I found PartSelect, easily found the diagram and correct part, and for less than $30.00 we ordered it and it arrived at our front door within 48 hours. You can't beat that for quality and fast service.
Thank you PartSelect.
Larry & Nancy Lukunich
Simi Valley, CA

1) Removed the two panels below the door.
2) Unscrewed the two screws holding the dishwasher to the upper cabinet facing.
3) Pulled dishwasher out 6-8 inches to gain access to springs located on the side.
4) Removed the broken spring.
5) Attached the new spring.
6) Openned and closed the door to make sure spring was tight enough.
7) Pushed dishwasher back in.
8) Rescrewed cabinet facing screws
9) Rescrewed floor panels.

Only problem was with ordering ... PartSelect part number is different than the FSP-Whirlpool part number. PartSelect should provide a cross-reference table if there is a difference between OEM number and PartSelect number.

Actually I ordered the drain and wash impeller kit because it was listed as the #1 cause of failure to drain. I then hired a plumber to install it. He did so and that didn't solve the problem. So I was about to buy a new dishwasher. I then noticed that the second most frequent cause was a problem with the "dishwasher drain check valve." I watched the "partselect" video on how to change that. I didn't have a new one but I thought I would take out the part and see what I could learn. As it turned out it was blocked by a little piece of what appeared to be a walnut chip. I cleaned it out reinstalled the drain check valve and the problem was solved.

Put in both a new element and thermostat. Did not fix problem. Using an ohm meter I did not measure any voltage to the thermostat. Suspect it’s a problem in the control unit, and decided to replace dishwasher.

Once the covers under the door are removed, the check valve is visible (unless its too dark, hence the headlight), and pointing right at you. Since I was working under the dishwasher, I gathered all the tools I thought I might need and laid them on the floor next to. Removed 2 covers, placed pan under check valve and hose to catch any water, squeezed clamp with (wrong) pliers, it eventually came loose. Carefully twisted hose off check valve. Water came out, some of it got into the pan, most of it on the floor. I guess I should have pumped it out before I started this. Plastic check valve is screwed into the big piece of whatever, carefully grabbed it with (wrong again) pliers and turned it out. Installation is reverse of removal - but use a large pliers with a ROUNDED jaw to grab the round check valve body. Don't squeeze too hard or overtighten it. Put the clamp on the valve before pushing the hose on. Be sure the hose seats all the way onto the little lugs. Compress the clamp, slide it over the end of the hose and release. That's all folks, works good now.

Mine is a Ultra Wash 111
I followed the repair video on your site but my dishwasher was a little different. Not enough that anyone could still understand the video and not get it disassembled. The video shows two ball checks but mine doesn't use them where the videos shows. I put them in anyway because I called Whirlpool, who made my washer, and they assured me that they should be in there. They got sucked through the dump impeller and plugged the discharge tube so I had to disassemble it again and take the ball checks out. Lucky for me nothing got damaged. I then got a hold of someone on your chat line that got me to the correct parts view that shows where the ball check is suppose to go on my washer. During working on my washer I realized the squealing was because the bottom bearing on the motor needed oil. So all and all I'm happy because it runs quiet and it works fine. Thanks Greg

Took the bottom panel off and felt with fingers to replace spring with out pulling dishwasher out from enclosure.
Fairly simple

Removed the inner door panel and then the circuit board protective cover (which just snaps in). Fuse assembly is readily accessible and just snaps in. The wires are attached with spade lugs using existing wiring. No wiring modificatins needed,