KUDC02IRWH2 KitchenAid Dishwasher - Instructions

First i remove upper rack held in by 2 clips at end of metal tracks. Compress inside clips and pull up then slide rack out of tracks.Then remove bottom rack just pick it up.Then i removed bottom sprayer by unscrewing center thumb screw. Then removed feeder tube for top sprayer held in place by 2 ea. phillips screws one on celin of tub and one at back of tub. Move tube to the right which unlocks it and remove. This has to be done to expose 4 ea. star screws. Remove screws and pop screen cover off. You have to take a towel and soak up water to expose bottom of inlets and outlets for water. You will then see the chopper blade with metal screen behind it. It is held in place with on star screw to the left of round top cover. Remove cover and pull on chopper blade which will release it from fingers mated from shaft to chopper blade .While pulling on chopper blade toward front of dishwasher pull up on metal screen it will come out. Clean all food particals out i used a shop vac worked well. Be careful not to drop screws in water inlets. The plastic shaft was broken in half by a piece of dental floss wrapped around shaft. I hope this helps it was not that diffacult just hard to work over door.

My husband pulled out the dishwasher and removed the faulty part and installed the new one. We found info on the parts source website to assist us. Dishwasher works great!!! Someone from the company we purchased it from had replaced it several years ago, and the seal at the bottom had leaked and the motor had siezed because of the water. We also discoved that the water line was severly kinked in 2 places, so we installed a flexable hose. Now my dishwasher is quiet, fills much faster and all this for a fraction of the price of a new appliance. Would recommend this website.

Remove two screws at top that fasten dishwasher to cabinet. Slide dishwasher out to expose the two links that attach the door to the springs. Fit the new links to the springs and door.

that there is 90% of the repair made easy when you have the correct part. there is no better then direct replacement parts. the repair was self explanitory. one screw, two lines, lock in place, done. thanks for having the correct parts,that is what makes a job simple.

The first thing I did to repair my diswasher was call a repair company. They wanted $175.00 just to look at it, so I scheduled an appointment. Then, I did an internet search for dishwasher repair. I learned about bi-metal fuses, and how to check them. I found my bi-metal fuse was bad, so I ordered a new one through parts select. My part arrived in two days. I installed it easily, and the dishwasher worked. Finally, I canceled the repair appointment.

Pulled out dishwasher. Took out old screws. Unsnapped end of rack slid new wheel in and attached to side. Very Very easy. It was great to get the part so fast and take care of this repair ourselves.

Removed old seal, cleaned track, applied adhesive for new seal, seated new seal in track, closed door for 24 hours to allow adhesive to cure, then used dishwasher without difficulty. An easy repair.

I removed the dishwasher from under the cabinet. This is what took the most time. Before removing the dishwasher from under the cabinet I disconnected the drain cable to remove all the water from unit. After removing the dishwasher I tipped the unit on its left side. The motor/pump assembly is held in with one screw. After removing this screw the pump/motor assembly comes out with a 1/8 turn counter clock wise. The replacement pump/motor assembly was put back in in reverse order. After the pump/motor assembly was replaced I replaced the door balance cable kit on the right side of the unit. Next I tipped the unit on to its right side and replace the left balance cable kit. After this all that was left was to return the unit back under the cabinet and hook up the water supply line, the drain line, and the power.

I watched the video and this was the easiest repair ever. Took longer to disconnect and reinstall than it did to change out the pump. Highly recommended watching the video

I snapped on the new part onto the track. It was that easy! :) Thank goodness the part was available from Part Select!
T. Edwards

Was able to replace and repair without taking the dishwasher out. Thermostat is behind and to the left of the power junction box. Has 2 wires going to it. It is up against the bottom of tub. I used an angled mirror to see what I was doing. 1 small screw to detach and pull down thermostat. Be sure power is off before you start. Also reprogrammed defaults. Hit any button 1-2-3, 1-2-3, 1-2-3, fast and close door. Let it sit 15 min to run and re-set defaults. Now I have heat and dry dishes.

My 2 parts were delivered very quickly. We had been putting off the repair, mainly because any time you hire a capable repair man, the charge to "walk through the door"is very high. I actually thought about buying a new DW for this reason . . . Then I googleD PARTS, And was lucky to find PARTS SELECT. I was most impressed with the graph layout of the parts, which enables the buyer to actually measure the part being replaced to be sure the correct item is being ordered. The instructions were excellent, and this grandmother took care of the repair, easily.

Shut the power to the dishwasher off. Pulled unit out from under the counter top and raised the left hand side up for easy access. Disconnected the wiring, undid the clips, turned counter clockwise and removed. Reversed the order for installation and Connected the power. Ran several cycles successfully. Problem fixed. Burnt out water pump. Good as new if not better so far. Easy item search, Fast Shipping, Quality Part, Fair Pricing. Thank You Partselect.com

This kit comes with the link cords and the balance wheels. I only needed the cords. I undid the set screws under the counter edge and slid the Dishwasher out from under the counter. One of the links had a broken cord and the spring had snapped to the very back of the space and was a bit hard to find. I used the good side as a guide to see how to thread the cord correctly. I did not replace the wheels since they appeared to be in good shape and looked like they might be a bit more difficult to replace than just the cord. For a second I thought I had ordered the wrong part because the new cord's attachment point at the hinge did not look exactly like the originals but the new design worked just like the original. I did need one other person to help stretch the spring and hold the door in the best position so I could attach the cord to the hinge. It's working perfectly now and I saved the wheels in case I need them later.

too simple to describe