KSSC48MHS00 KitchenAid Refrigerator - Instructions

The instructions are practically no help, but if you study the diagram, you can figure out the one screw you need to remove. Then the icemaker lift off of two brackets. I couldn't see how to use a screwdriver to unlock the bracket, but just applying mild pressure and pulling it forward brought it right out. I didn't have to change anything with the plug already intalled so it was very easy to pop in, lock the plug, pop into brackets, replace screw and I was in business. 24 hours later I had a bucket of ice! 15 minutes to figure out how to get old out and 5 min to replace new one. Fairly easy. Read posts here to get hints!

removed three screws pluged it in and it was ready to go. I must add That I ordered it one day and received it the next day by fed ex. I could not believ how fast the service was also the new icemaker is working great. I will order any furture parts I need from Parts Select. Also have given your web site ot several other people. Thank you very much.

Got on line with Partselect and follow their directions. It was very easy.

I just followed the instructions that came with the unit, it was very easy. The old ice maker was taken out some time ago, so all I had to do was install the new one. It was three screws and one electrical plug. I removed the ice maker over a year ago and did not replace it at the time. I purchaced new handles also and they were easy to replace. I then decided to try the ice maker, I got tired of buying ice at the store. The order came in just two days right to my front door. It was a very easy fix and now I have a refrigerator full of ice. Thanks for the great service.

Unplugged refrigerator and turned off water supply. Loosened two top screws and removed bottom screw. Althought kit was supplied with multyple wiring harnesses the harness attached to unit was the correct harness for the model I was replacing. Removed and reused old shut off arm as replacement arms were shorter in reach then original. Also reused bottom unit support that was removed and replaced with one screw into unit and then into side wall of freezer. Over all time less then 15 minutes. As this was a side by side ref/freezer unit their us limited space to view support screws. I used a mechanics mirror to find upper screws. This visualization made the process go much faster. Reading the other repair stories also gave me a huge confidence boost and insite in what to expect.

I loosened the two screws on which the ice makers hangs and removed the third screw toward the back. I lifted the icemaker a bit and removed the part and unplugged the unit at rear. I reversed the process to install the new one. All very simple.

At first nothing happened, no water filling the tray. I thought there must be some other problem. A few hours later I heard ice being dumped into the ice container. I don't understand the delay but it works fine.



At first no

I removed the icemaker. One screw at the bottom and then unplug the electric. Remove the old motor from the face that has 3 screws holding it. Put the new motor in. A very simple job. I now have a full ice bin by the next morning.

I just removed the unit and replaced the mold/'heater with the new one and re-installed. It was very easy and didn't have to turn off the refer. or empty the frozen food.
However , there were not instruction that came with the mold/heater unit. I had no problem but other do-in-uselfers may need some basic instructons
Jim

We followed the video on the KitchenAid website. We turned off water valve at the wall, unplugged the refrigerator, removed the old icemaker by unscrewing the three mounting screws. We unplugged old icemaker from electrical source at back of refrigerator freezer compartment and removed it. We detached the on/off bar from the old icemaker and installed it on the new icemaker. The new icemaker fit perfectly. We plugged in the electric wire to the existing power cord at the back of the refrigerator freezer compartment. We placed the new icemaker in the same position as the old, making sure the mounting screw holes were aligned. Plugged refrigerator back in and turned on the water. Works beautifully.

The bearing & cup assembly was broken and the gears in the drive assy were stripped. Unfortunately I couldn't find anywhere to buy the gears without buying the entire motor assy with the gear box already on it. Cost was up to $85 with shipping but at least it now works fine.

To repair: a 1/4 nut driver will take off screw below ice maker and all you need to do is loosen the 2 screws above the ice maker then push it upward slightly and it will slide off the top 2 screws. Then pull the power connector off from behind the ice maker at the side of the refridge. Then pull straight out and it will slide off the water fill tube. Now with unit out of refridge I took the cover off the front of the ice maker and removed the 3 philip screws. I then pulled the motor/gear assy off from the chassis of the ice maker. I then had to remove the 2 philip screws on the chassis (under the motor/gear assy) to remove the cube maker/element from the chassis. This allowed me to remove the rotating cube spatula bar to replace the filler cup/bearing assy. Then I reinstalled the spatula bar and the 2 philip scews on the chassis to the cube maker/element assy. I then installed the new motor/gear assy to the chassis and installed the 3 remaining philip screws. Put the cover back on the ice maker and inserted assy back into the refridge by first reattaching the power connector and then sliding backward onto the water fill tube and then slipping over the top of the 2 top screws on the refridge. Then I installed the screw below the ice maker and tightened all 3. Presto - repair done in 30 minutes and perfect cubes were spitting out within the hour.

I removed the 2 screws on top and the one screw underneath holding the Ice Maker to the wall of freezer.I pulled the electrical connection from the wall next (wiggled it back and forth until it came out).
I matched it up to the picture from this site and ordered the replacement unit.
When it arrived, it had a lot of extra parts to match up to mine and any other fridge.
A good tip is to keep the old unit so you can configure the new unit the same. Although it was easy, this took me the longest of the entire job. Once this was done, it took me !0 minutes to plug the new unit into my fridge and then attach it back to the wall with the 3 screws.Not a hard job.Thanks

The repair was simple.

I first did a diagnosis of the optical cuircuits and found them good. The tray heated up and when resetting the moor controller, the water cyccled to fill the tray so the only other thing it could be was the motor controller.

removed the service door for the ice maker
I removed the wire protectore screw and shroud
pulled the icemaker unit out and unplugged the unit
removed the motor controller end cap
unscrewed 3 screws holding the motor controller
removed and replaced the motor controller. ensured that all wire harness connector poiints were solid
reverse the above instructions and in 5 hours I was getting ice again!

$90 turned out to be a savings from the $250 it would have cost to have someone come out and look at the fridge.

I highly recommend to anyone who can read and use a screwdriver to perform this repair if you have diagnosed this as the root of your problem!

Used a nutdriver and removed the lower mount nut, then loosened the the top two nuts and the icemaker lifted off, then unplugged the device and replugged it into the "old" plug(the new ones were not needed) then remounted it. Then it did not fill (as others posted happened right away.) Some poster suggested manually filling the tray so I did it. Later it froze and emptied and refilled and started working normally. Not sure if putting water had anything to do with it or it just took some time. It would be nice if the instructions addressed this issue.

Removed Ice tray and flap followed by the three screws that held the old ice maker in place. (I probably didn't have to remove the top two, they are designed to just loosen and lift up on the mecanism to free.) I then pulled the old wiring harness out of the original ice maker. A small screw driver helped in depressing a tab while pulling on the harness. The same process was used to remove the wiring harness that was attached to the new replacement unit. I connected the original wiring harness that I had disconnected from the bad ice maker, and it fit perfectly into the replacement unit. No need to splice or use any of the harnesses that came with replacement. I tried installing the new unit and discovered that there was interfernce with the water feed hose. I had forgotten to break off the tab on the end of the replacement unit. Once I did that using pliers, the unit fit fine. I tightened the screws, installed the on/off mecanism and replaced the tray and flap. I then waited and waited, hoping to hear the forgotten sound of water entering the ice maker. Had a beer and walked the dogs thinking I had failed, but low and behold, over an hour later, the ice maker turned on the water. Many hours later, my wife woke me up in the middle of the night to declare we had cubes! Success.

Repair was real easy, I had to remove several screws in the bottom of the icemaker module housing. The unit slide out with no problem there was a wire assembly that hat to be disconnected but this did not present a problem. The old module came out real easy after removing 4 screws and the replacement was not a problem to but in.