KSSC36FTS04 KitchenAid Refrigerator - Instructions

Removed icemaker found ice mold protective layer coming off. Replaced ice mold and working great. Online graphic very detailed and easy to determine part needed. Easy and great delivery. Highly recommended for future repairs.

took off old filter put in new - simple

My ice maker would not produce ice. I removed motor module which involved removing ice maker from freezer, removing motor module cover and 3 screws. I found short (burnt place) in copper of existing module. Ordered new motor module, replaced, and all is fine. Great service, quick delivery and correct part.

Popped the old one out with a kitchen knife and popped the new one back in. It tool less than 15 seconds!!

My owners manual said to unplug fridge from elec outlet, use a kitchen knife to gently pry off the switch plate
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!

Sincerely, Ron Marshall, Billings, MT

I pried the old one out with a screw driver and pushed the new one in. I expected instructions in the box it came in but there were none.

Loosen to screws under ice mold and unplug power cord from icemaker.Lift out complete unit. Remove cover on ice maker,then 3 screws on end plate and remove end plate. Remove 2 screws that hold ice mold to frame. Make sure that the thermostat is moved to new mold. Reverse order to install new mold.

Used the instructions on your site.

Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.

Had to Test Seloind. It Was OK. Then tested Motor Motor For Ice Maker. It Was Bad. Went Online Looked Up Parts For My Unit. They Were Shipped in a Timely Manner, only a few days. Installed parts in less than 15 minutes. Went very easy. Thank You

I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.

It was simple using PartSelect to locate the likely source of the problem. Also the pictures of the part helps confirm that you have the correct item.

Got the main bolts off and unplugged and removed the ice maker. Had to remove all parts and rebuild it on the new mold. Was more complex than I thought but was able to get it done. Note where everything was as you take it off and you'll do fine.

The noise seemed to be coming from the closing cam at the top of the door, so we figured it had worn over time and was no longer operating smoothly, but rather popping into place when the door was opened all the way. We ordered a new cam, which was about $20 for a quarter-sized piece of metal with two holes in it. Expensive for what it was, but cheaper than calling a repair person for sure. Our first problem was how to disengage the spring that closes the door. It was hard to get a purchase while standing on a stool and the tension on the spring was very tight. Finally my husband rigged up a sort of pulley system to get more leverage and was able to get the spring off. The next problem was removing the screw that held the cam assembly in place. We were afraid we were going to have to saw it off, but finally my husband was able to remove it and it was barely salvageable to reuse with the new cam. After that, reassembling the system with the new part and reattaching the spring was relatively straight forward. The good news is, no more annoying popping sound!

The refrigerator stopped working and temperatures were rising. After inspection, noticed that the compressor is not running and condenser fan not running. I ordered the inverter box and replaced the old one. Compressor started to run but condenser fan still not running. Compressor was getting hot while freezer temperature reduced to some degree. Cleaned condenser with compressed air, connected condenser fan directly to 110VAC. Refrigerator runs normally. Burning of the inverter box may be preventable. We did notice that the freezer portion of the door frame getting hot for over 3 months. This is an indication that the condenser does not provide sufficient heat dissipation. This in turn made the compressor hot and melted away some components in the inverter box which is located next to the compressor. A thorough cleaning of the condenser made the freezer door frame stay slightly warm but not hot. This condition keeps the compressor running at normal temperature. I still need the main controller which is discontinued to automatically control the condenser fan. So far the fan runs all the time and uses a bit more electricity than necessary.