Includes both the attachment and beveled gear. This worm follower gear is for stand mixers.
Worm follower gear meshes with the worm gear, causing the rotation of the planetary assembly where the ac...
$38.95
In Stock
Order within the next 9 hrs and your part ships today!
Keep your stand mixer running smoothly with this replacement worm gear, which powers the planetary assembly where beaters and other attachments connect. Made from high-quality metal, it’s built to wit...
$69.67
In Stock
Order within the next 9 hrs and your part ships today!
If your stand mixer isn’t adjusting speeds like it used to, this speed control switch might be the fix. It comes with the black knob and lets you fine-tune how fast your mixer runs—perfect for everyth...
$136.14
In Stock
Order within the next 9 hrs and your part ships today!
NOTE: This part has been upgraded from plastic to metal housing. Gasket is no longer available separately.
***Used with Stand Mixers.
$77.16
In Stock
Order within the next 9 hrs and your part ships today!
Questions And Answers for KP26M9PCBM5
Ask our experts a question about this model and we'll get back to you as soon as possible!
1 question answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Helene
April 8, 2025
Aussitôt qu’il sent une résistance le fouet ou le batteur ne tourne plus.
Même si le moteur tourne très bien
Merci
For model number KP26M9PCBM5
Bonjour Hélène, merci de nous avoir contactés. Après avoir étudié votre modèle, le problème peut être dû à un engrenage desserré ou endommagé, à un jeu trop important ou trop faible du batteur, ou au réglage de la vitesse. Vérifiez d'abord la vis de réglage de la hauteur du batteur à l'arrière de la colonne, au-dessus du support du bol, et essayez d'ajuster la hauteur du batteur pour voir si cela résout le problème. Sinon, vérifiez les engrenages internes du carter d'engrenages pour détecter une usure excessive. Vérifiez également l'interrupteur pour tout dommage visible. Bonne réparation. Hello Helene, Thank you for contacting us. Researching your model, this can be caused by a loose or damaged gear, the beater clearance being too high or too low, or the speed control. First check the beater height adjustment screw on the back of the column above the bowl support and try adjusting the beater height to see if that fixes the issue. If not, then you may need to check the inner gears inside the gearcase for excessive wear and tear. Check the switch as well for any visible damage. Good luck with your repair.
removed metal strap around motor housing then remove the 4 screws holding top motor cover on, then removed the 4 screws that hold gear cover in place, remove long gear that is driven by the motor gear, then with ring pliers remove ring off long drive shaft and lift off worm gears. once all gears are removed --removed all the old grease ( do this to get all the metal shavings out from the failed gear) repace the grease in the gear housing and reassemble in reverse order
1, Removed trim piece (1 screw) 2, removed cover (4 screws) 3, removed speed switch assembly (2 screws) 4, removed gear cover (4 screws) 5, removed and examined 2 worm gears for wear. Gear cover was badly cracked, don"t know if it was caused by a previous repair or by heat, as old cover is plastic. Received new parts and installed them, 2 bearings, 2 worm gears, 1 new cover of diecast metal and a new gasket. All repairs made with a #2 phillips screw driver. My wife then made bread, and it preformed flawlessly.
Removed screw from back of mixer cover band and then removed the 4 side screws, lifted top off of mixer and removed screws from circuit board control switch, removing wires one at a time so as to install correctly. replaced screws in circuit board/control. Restored top of mixer replaced screws and the put cover band back on mixer.walla done
