Includes both the attachment and beveled gear. This worm follower gear is for stand mixers.
Worm follower gear meshes with the worm gear, causing the rotation of the planetary assembly where the ac...
$38.95
In Stock
Order within the next 7 hrs and your part ships today!
Keep your stand mixer running smoothly with this replacement worm gear, which powers the planetary assembly where beaters and other attachments connect. Made from high-quality metal, it’s built to wit...
$69.38
In Stock
Order within the next 7 hrs and your part ships today!
If your stand mixer isn’t adjusting speeds like it used to, this speed control switch might be the fix. It comes with the black knob and lets you fine-tune how fast your mixer runs—perfect for everyth...
$129.75
In Stock
Order within the next 7 hrs and your part ships today!
This part is used with the stand mixers attachments, as well as to hold the end cap to the front of the mixer.
$35.75
In Stock
Order within the next 7 hrs and your part ships today!
Questions And Answers for KP26M1XWH5
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Bill
December 2, 2019
My mother has owned this 6 quart kitchen aid mixer and she dropped it on the floor. After helping her to pick it up off the floor she plugged it in and now the speed control does not work. All it will do is 2 positions "off or full power" and i would like to get it fixed to pass it along to her granddaughter who used it with her grandmother. Any information would be useful. Thanks , v/r bill emhoff
For model number KP26M1XWH5
Hello Bill and thanks for writing.
You can replace the speed control assembly part # PS11746948. This way the granddaughter should still get a lot of use out of this unit. We hope this helps. Please contact us anytime.
looking for attachments for this model - dough hook, beater and whip. stainless steel is preferred.
Thank you!
For model number KP26M1XWH5
Hello Dawn, The Dough Hook PS16875730 is made of metal and has a burnished finish. The Wire Whip PS11746914 also has a burnished finish. The Flat Beater The Flat Beater PS16875729 is made from metal and has a burnished finish. We look forward to hearing from you.
removed metal strap around motor housing then remove the 4 screws holding top motor cover on, then removed the 4 screws that hold gear cover in place, remove long gear that is driven by the motor gear, then with ring pliers remove ring off long drive shaft and lift off worm gears. once all gears are removed --removed all the old grease ( do this to get all the metal shavings out from the failed gear) repace the grease in the gear housing and reassemble in reverse order
1, Removed trim piece (1 screw) 2, removed cover (4 screws) 3, removed speed switch assembly (2 screws) 4, removed gear cover (4 screws) 5, removed and examined 2 worm gears for wear. Gear cover was badly cracked, don"t know if it was caused by a previous repair or by heat, as old cover is plastic. Received new parts and installed them, 2 bearings, 2 worm gears, 1 new cover of diecast metal and a new gasket. All repairs made with a #2 phillips screw driver. My wife then made bread, and it preformed flawlessly.
Removed four screws to remove main cover. Removed four more screws to remove fractured plastic gear housing cover. Removed retainer ring and slid two gears and dowel off main shaft. Lifted out remaining gear train and bearings, Removed all grease and metal chips from all components. Greased new gears and reassembled. Replaced plastic gear housing cover with oreviously purchased die cast replacement part. Assembled main cover.
