Includes both the attachment and beveled gear. This worm follower gear is for stand mixers.
Worm follower gear meshes with the worm gear, causing the rotation of the planetary assembly where the ac...
Keep your stand mixer running smoothly with this replacement worm gear, which powers the planetary assembly where beaters and other attachments connect. Made from high-quality metal, it’s built to wit...
If your stand mixer isn’t adjusting speeds like it used to, this speed control switch might be the fix. It comes with the black knob and lets you fine-tune how fast your mixer runs—perfect for everyth...
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Robert
January 30, 2023
I am looking for two gears that are used for the grinder attachment for mixer KP2671xwh. Your website does not show this model number. However, it does show KP2671xwh1, kp2671xwh2, kp26713. Are any one of these model numbers equal to my model number? Thanks, Bob
For model number KP2671XWH1
Hello Robert, Thank you for writing. The Gears for the KP2671XWH would be the same as KP2671XWH1, KP2671XWH2 and KP2671XWH3. The Number is for the color of the appliance, the gears are the same. We hope this information helps!
2 peoplefound this helpful.
Was this helpful?
Thank you for voting!
Gerald
June 6, 2023
looking for replacement parts, gears for my mixer
For model number KP2671XWH1
Hi Gerald, thank you for reaching out. Your mixer comes with the following gears: Stand Mixer Pinion Gear, part number PS12347635, Worm Gear, part number PS11747012, Worm Following Gear, PS12070620, and Hub Gear, part number PS12348886. Your model requires 2 Hub Gears. We hope this helps!
My model info plate did not have a number after it. My mixer still runs, but is mixing very slow. It is as if the mixing fork is not tight on the shaft. My question is after 19 years, what parts or kit should I order to bring my mixer back to normal operating condition? Thanks in advance for your help!
For model number KP2671XWH1
Hi Jim, Thank you for writing. We suggest opening it up and checking all of the gears for wear or damage as well as the Planetary. Let us know if you have further questions!
removed metal strap around motor housing then remove the 4 screws holding top motor cover on, then removed the 4 screws that hold gear cover in place, remove long gear that is driven by the motor gear, then with ring pliers remove ring off long drive shaft and lift off worm gears. once all gears are removed --removed all the old grease ( do this to get all the metal shavings out from the failed gear) repace the grease in the gear housing and reassemble in reverse order
1, Removed trim piece (1 screw) 2, removed cover (4 screws) 3, removed speed switch assembly (2 screws) 4, removed gear cover (4 screws) 5, removed and examined 2 worm gears for wear. Gear cover was badly cracked, don"t know if it was caused by a previous repair or by heat, as old cover is plastic. Received new parts and installed them, 2 bearings, 2 worm gears, 1 new cover of diecast metal and a new gasket. All repairs made with a #2 phillips screw driver. My wife then made bread, and it preformed flawlessly.
Removed screw from back of mixer cover band and then removed the 4 side screws, lifted top off of mixer and removed screws from circuit board control switch, removing wires one at a time so as to install correctly. replaced screws in circuit board/control. Restored top of mixer replaced screws and the put cover band back on mixer.walla done
