KP220WDW-2 Frigidaire Range - Overview
Sections of the KP220WDW-2
[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Terminal Block Kit
PartSelect #: PS470125
Manufacturer #: 5303935058
This surface burner terminal block kit comes with interchangeable mounting brackets, terminal box, ceramic wire nuts, heat shrink protective tubing and wires.
$19.49
In Stock
Drip Bowl - 8"
PartSelect #: PS437595
Manufacturer #: 316048413
This drip bowl is located beneath the element and catches any spills. It is sold individually and has a diameter of approximately 10 inches.
$18.65
In Stock
Chrome Drip Bowl - 6"
PartSelect #: PS437596
Manufacturer #: 316048414
This drip bowl is sold individually. This part is located beneath the element and catches spills from cooking.
$17.55
In Stock
Surface Element - 8 Inch - 2600W
PartSelect #: PS2339242
Manufacturer #: 316442301
This surface burner element is eight inches in diameter. It has five turns, 2600 watts and looped terminal ends. The element provides heat to the cooking surface on your range. If your element is not ...
$48.35
In Stock
6-Inch Coil Burner Element
PartSelect #: PS2368974
Manufacturer #: 318372211
This element has looped terminal ends and comes with a black medallion center. This element is a genuine OEM replacement part, has looped terminal ends, comes with a black medallion center, and fits m...
$40.65
In Stock
Burner Switch Kit
PartSelect #: PS470145
Manufacturer #: 5303935086
This switch controls the stove top surface burner.
$65.41
In Stock
4' 40 AMP 3 WIRE RANGE CORD, BAGGED
PartSelect #: PS12746172
Manufacturer #: 5304512983
No Longer Available
Common Symptoms of the KP220WDW-2
[Viewing 3 of 3]Element will not heat
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Oven not heating evenly
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
burner shorted out
I followed the directions by clipping wires to old burner socket, splicing the wires to new terminal block, screwing down new "block bracket," and plugging in new burner.
Parts Used:
-
David from Encinitas, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
61 of 75 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old pans/bowls were corroded
Very easy---simply unplug the burners, remove the old pans and replace with the new ones
I was extremely pleased with the easy ordering and prompt delivery of parts that actually fit as they should!
I was extremely pleased with the easy ordering and prompt delivery of parts that actually fit as they should!
Parts Used:
![](/437596-1-S-Frigidaire-316048414-Chrome-Drip-Bowl-6-amp-quot.jpg "Chrome Drip Bowl - 6" – Part Number: 316048414")
![](/437595-1-S-Frigidaire-316048413-Drip-Bowl-8-amp-quot.jpg "Drip Bowl - 8" – Part Number: 316048413")
-
John from Nisswa, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
48 of 55 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
High heat reluctant to turn down.
Most of the job is simple fastener mechanics.
Use a nut driver or Phillips screwdriver. Remove rear panel.
Pull out control knob. If it is stuck, wrap a small rag around the back of it and pull the rag steadily.
Carefully match marked terminals on the replacement switch with those on original. Switch terminals may not be in the same location. Replace wires one for one, one at a time.
Carefully select the correct knob filler for the switch post. Several are supplied. Proceed with logic and measure the shaft length and the filler length and type to match.
Use a nut driver or Phillips screwdriver. Remove rear panel.
Pull out control knob. If it is stuck, wrap a small rag around the back of it and pull the rag steadily.
Carefully match marked terminals on the replacement switch with those on original. Switch terminals may not be in the same location. Replace wires one for one, one at a time.
Carefully select the correct knob filler for the switch post. Several are supplied. Proceed with logic and measure the shaft length and the filler length and type to match.
Parts Used:
-
George from New Port Richey, FL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
45 of 49 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!