KGCP467JTL0 KitchenAid Cooktop - Overview
Sections of the KGCP467JTL0
[Viewing 2 of 2]
Manuals & Care Guides for KGCP467JTL0
Click to downloadKeep searches simple, eg. "belt" or "pump".
Burner Grate Pads - Kit of 5
PartSelect #: PS389174
Manufacturer #: 814323
These pads go on the bottom of your gas cooktop grates to prevent them from moving and scratching the top of your appliance.
$17.25
In Stock
Screw
PartSelect #: PS12349731
Manufacturer #: W11233072
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
$28.95
In Stock
Range Torx Screw
PartSelect #: PS11741257
Manufacturer #: WP3368921
7-18 x 3/4-Inch - sold individually.
$8.95
In Stock
Range Burner Spark Electrode
PartSelect #: PS11747153
Manufacturer #: WP9754215
Also known as spark electrode. This part helps your burner ignite and produce flame.
$63.75
In Stock
Control Knob
PartSelect #: PS11748161
Manufacturer #: WPW10078400
Sold individually. This knob accepts a D-shaped shaft.
$13.15
Special Order
Refrigerator Screw
PartSelect #: PS11740992
Manufacturer #: WP3196557
Sold individually.
$10.59
In Stock
Range Spark Module
PartSelect #: PS11744828
Manufacturer #: WP8053421
This part sends enough current to the igniter to create a spark to the bottom of the burner cap.
$180.48
In Stock
Burner Cap - 14000 BTU
PartSelect #: PS375413
Manufacturer #: 4455243
Sold Individually.
No Longer Available
Top Burner with Spark Electrode - 6K - Right Front/Left Rear
PartSelect #: PS389258
Manufacturer #: 814512
No Longer Available
Regulator
PartSelect #: PS11747235
Manufacturer #: WP9759091
This part makes sure that no gas is released until the igniter gets enough power to ignite the gas range and automatically cuts off the flow of gas at a certain pressure.
$236.52
In Stock
Common Symptoms of the KGCP467JTL0
[Viewing 2 of 2]Will Not Start
Fixed by
these parts
these parts
Show All
Gas igniter glows, but will not light
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
several grate pads fell out/lost /broke during cleaning
The only real issue was locating the proper adhesive to ensure that the new pads would not fall out. The small insert paper slip in the package noted that a RTV adhesive should be used. After much searching at the home improvement super store, I learned it would be found at an auto supply store. It is black, and is for high temp use. It is available in a small tube for around $2.00. The RTV is usually used to make gaskets for heat/oil exposure in auto repair. I did have trouble removing a broken stub from a pad that had broken off in the hole. I used an awl to get what I could and push the rest into the hole deeper, then insert a new pad with along with the adhesive.
Parts Used:
-
Sabrina from Mooresville, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
61 of 67 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rubber pads on bottom of grate broke off, grate was scratching stainless steel top
I just put the grate pads in the bottom of the grate. The repair was a snap.
Parts Used:
-
Melissa from The Woodlands, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
13 of 20 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Missing bumper pads
Original bumper pads NOT glued into the burner grates. Hence they began to disappear during routine use and cleaning. Very simple repair with a little glue this time around. But fairly expensive for a very small part set
Parts Used:
-
Martin from Denver, CO
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
7 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!