KEBV107PMT00 KitchenAid Wall Oven - Instructions

Repair was very easy, Alittle time consuming. Unscrewed the outer skin of the door and removed the pieces.

My story isn't so much about the repair but the fine service from part select. My 1st order was lost at delivery at our house. Part select quickly corrected the mishap with no issues. This kind of service is much appreciated.

I did not take the door off the oven, i dissassbled it in place. all the visible screws on the door have to be removed. The "vent" air diflector or what ever it is , between the upper and lower doors has to come off also to access the screws that hold the front of the door on. The only confussion i had was the bracket that holds the third layer of glass. I forgot that it is held on with the same bracket/screws that hold the secound layer on.

I just removed the door and change the glass. Really easy.

Removed Door, Took Door apart, Replaced glass, re-installed door. Pretty basic

1) Look for the part at partselect.com, make sure you have the model and part number ready. Once you find the part, don't order yet. 2) Start your do-it-yourself repair by removing the oven door. On each side below are two arms/hinges, look closely and you will find locks on each side. Use your finger or flat screwdriver to slide towards you (this is where you start clicking your camera in evey step). Once you did it, wiggle the door a little bit, make sure they're unlocked, then pull it out carefully and hold it tight since it's little heavy. 3) At this point, you only need the phillips screwdriver. Look for all the screws, and unscrew it all, one step at a time (again make use of your digital camera). Remove the parts one at a time until you take out the broken inner glass. Measure it against the dimensions shown in the partselect.com. At this point you feel comfortable putting it back in-reverse, then you order the part. It took me 3 days for the part to arrive, but it's no big deal. 4) It's a bit difficult for me the first time, I can't figure out how to put them back (that's why I recommended the digital camera), plus I have to clean the inside and the other two glasses so it took me 1-2 hrs. I assure you if you follow my instructions, 15-30 minutes max, no sweat. 5) My wife promised me $300 for the labor (competitive price), I'm still waiting though.....Good Luck

Unwrapped the package, plugged the probe into the oven, stuck the other end into the chicken.

I ordered the part online and after recieving it I downloaded the manual from kitchenaid online and it explain exactly how to replace this part and I followed the instructiones and it worked with not too much difficult . It took me about an hour between reeding the instructions and doing the job itself

opened door and secured the open position with a 3/8 allen wrench through the hole at the base of the support arm. (small bolt or other round, short object can be used). This locks the door in a 75% open position. Locking the door open allows easy lift and removal. Six screws and the door is apart. Clean and reassemble.

Unlocked the latches that hold door into oven. Removed door to work on it. Disassembled door by removing all the screws that hold it together. Removed two other glass sheets to access location. Cleaned out broken glass. Installed new glass sheet and reinstalled two other glass sheets. Reassembled door and reinstalled in oven. Not difficult, just a fair number of parts and pieces to take apart and put back together.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

shook bottle and painted waited a day and repeated

I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.

Removed wall oven from wall. Removed back cover. Unscrewed thermastat and removed old thermastat. Screwed in new thermastat and put back together.

Had no problem replacing the glass it took my Husband and I less than 30 min. It took only a screw driver and that's it. Very easy