This OEM Dishwasher Upper Rack Adjuster is a grayish-black, plastic part which will require a screwdriver to install. It fits onto the dishwasher rack and connects it to the track allowing it to slid...
This gray plastic lower dishrack roller is a part for your dishwasher. It attaches to the bottom of the lower dishrack, allowing it to move in and out smoothly. If the lower dishrack stops moving in a...
Sold individually. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking, or tilting forward.
Also known as rack adjuster. Sold individually.
This is an original part from KitchenAid, Kenmore, Whirlpool, Jenn-Air, and Maytag for use with Dishwashers. The dishrack adjuster arm positioner clip...
This part is the replacement door seal for your dishwasher. It is approximately 22 inches long and 2 inches wide. This door seal is made of gray plastic and is found at the bottom the dishwasher. The ...
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
Sold individually.
This dishrack adjuster is for dishwashers.
Dishrack adjuster lets you change the height of the dishwasher's upper rack.
Wear work gloves to protect your hands when installing this part.
$58.76
In Stock
Questions And Answers for KDFE104DSS0
Ask our experts a question about this model and we'll get back to you as soon as possible!
6 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Ron
September 9, 2021
Why does my sanitize light continue to blink until i open the door. Plus i notice the dishwasher is noisier than before?
For model number KDFE104DSS0
Hello Ron, Thank you for your inquiry. We have researched your model and the sanitize light will blink if the water does not get hot enough to sanitize the dishes. First, check the temperature of the water going into the dishwasher, it should be at the minimum temperature of 120 Fahrenheit. If it is hot enough, then check the heating element, the door latch and the control board. If it is noisy, you also want to check the motor, drain pump, and the inlet valve. You can test the parts with a multimeter. If you are unfamiliar with how a multimeter functions, we have videos available to assist you. Good Luck with your repair!
Wish to purchase "Access Panel" only Metal or plastic
For model number KDFE104DSS0
Hello Robert, thank you for getting in touch. The compatible access panel for your model is part number PS11755984. It is made up of metal. We hope this information is useful!
Hello Nina, thank you for reaching out. The dimensions of your model are: height: 30 inches, width: 23 7/8 inches, and depth: 24 1/2 inches. We hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Robert
March 19, 2023
Soap residue and terrible water spotting after cleaned. Could it be the rinse arm being calcified?
For model number KDFE104DSS0
Hi Robert,
Thank you for your question. If you are using too much soap in your dishwasher, you will have a spots and a soapy residue left on your dishes. Use less soap and use the soap recommended in your owner's manual. If you have any questions, please let us know. We look forward to hearing from you!
Was this helpful?
Thank you for voting!
Pat
December 8, 2023
I run the diagnostics and get error code 6-4, float switch. The dishwasher is not drying the dishes. I tested the element and get 13 ohms. The thermostat has continuity -0 ohms. I looked at the float, it is moving freely and clean of debris. The float switch clicks. Should I test the continuity of the switch?
For model number KDFE104DSS0
Hi Pat, thank you for contacting us. The 6-4 error code means the float switch in your dishwasher has a problem. You should also check that the water inlet valve, part number PS12578165, is working properly because if your dishwasher fills with too much water, the float switch will activate. Glad to be of assistance!
Pulled dishwasher from under counter, attached link to spring, hooked spring back into frame/chassis, threaded link through pulleys, attached other end of link onto door, reinstalled dishwasher under counter. All's well. Note-I purchased an extra link anticipating that the other one will fail. They're cheap enough.
Caviat: The actual repair is less than 15 minutes, but I spent a lot of time playing with it before I figured out it was that easy and fast. You don't need to remove the dishwasher from the counter to do this. And it will probably help to look at the new part closely so you can understand where the retainer clip is to press it and release the old pump.
First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done.
1. Open the dishwasher and remove the two plastic grommets about halfway down on either side of the opening. Then remove the two screws under the grommets.
2. Remove the kick plate under the door. May have to lower unit by turning the feet using the adjustable wrench.
3. Make sure you have enough slack in the water input line and electrical wiring that you can pull the dishwasher out about 12 inches or more.
4. There is a spring and nylon rope link on both sides of the unit. Probably just one link is broken, but the replacement comes with two, so you can replace both or save one as a spare. Look at the good side and it should be pretty self explanatory how it attaches. I found it easiest to first thread the link around the lower pulley, then attach the link to the spring, then spring to the rear support, then the link to the door.
