KD2661KATRW KitchenAid Mixer - Overview
Sections of the KD2661KATRW
[Viewing 4 of 4]
Keep searches simple, eg. "belt" or "pump".
Worm Following Gear
PartSelect #: PS12070620
Manufacturer #: W11086780
This is a manufacturer-approved gear, used in stand mixers.
$31.65
In Stock
Hub Gear
PartSelect #: PS12348886
Manufacturer #: W11192795
Includes both the attachment and beveled gear. This worm follower gear is for stand mixers.
Worm follower gear meshes with the worm gear, causing the rotation of the planetary assembly where the ac...
$35.88
In Stock
Mixer Worm Gear
PartSelect #: PS11747012
Manufacturer #: WP9709231
Keep your stand mixer running smoothly with this replacement worm gear, which powers the planetary assembly where beaters and other attachments connect. Made from high-quality metal, it’s built to wit...
$66.36
In Stock
Dryer Retaining Ring
PartSelect #: PS11746909
Manufacturer #: WP9703438
This metallic retaining ring is less than an inch in diameter. It is made entirely of metal.
$9.99
In Stock
Mixer Retaining Ring
PartSelect #: PS11746917
Manufacturer #: WP9703680
Used on Stand Mixers.
$11.99
In Stock
Stand Mixer Gear Grease
PartSelect #: PS12583821
Manufacturer #: W11200218
This Stand Mixer Gear Grease lubricates the moving parts of the stand mixer.
$103.29
In Stock
Stand Mixer Speed Control Board and Knob (Black)
PartSelect #: PS11746947
Manufacturer #: WP9706648
If your stand mixer isn’t adjusting speeds like it used to, this speed control switch might be the fix. It comes with the black knob and lets you fine-tune how fast your mixer runs—perfect for everyth...
$125.33
In Stock
Mixer Retaining Pin
PartSelect #: PS11746974
Manufacturer #: WP9707223
This part works in conjunction with the worm and bevel gear.
$11.99
In Stock
Mixer Thumb Screw
PartSelect #: PS11747009
Manufacturer #: WP9709194
This part is used with the stand mixers attachments, as well as to hold the end cap to the front of the mixer.
$34.19
In Stock
Gearcase Housing with Gasket
PartSelect #: PS1871466
Manufacturer #: 8212396
NOTE: This part has been upgraded from plastic to metal housing. Gasket is no longer available separately.
***Used with Stand Mixers.
$76.21
On Order
Wire Whip
PartSelect #: PS11746914
Manufacturer #: WP9703491
This part is the replacement wire whip for your stand mixer. It is made of metal and is approximately 7 inches from top to bottom, and 5 inches from side to side. The wire whip is an attachment which ...
$43.53
In Stock
Bowl Arm Lift
PartSelect #: PS11746961
Manufacturer #: WP9706885
This is a replacement bowl arm lift for your stand mixer. It raises and lowers the mixing arm in the bowl. It is made of white plastic and is sold individually. This part can also be known as the bowl...
$12.77
In Stock
Questions And Answers for KD2661KATRW
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the KD2661KATRW
[Viewing 2 of 2]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Plastic gear housing in stand mixer fractured causing gears to crash
Removed four screws to remove main cover. Removed four more screws to remove fractured plastic gear housing cover. Removed retainer ring and slid two gears and dowel off main shaft. Lifted out remaining gear train and bearings, Removed all grease and metal chips from all components. Greased new gears and reassembled. Replaced plastic gear housing cover with oreviously purchased die cast replacement part. Assembled main cover.
Parts Used:
-
WES from BREVARD, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
70 of 107 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
wouldnt turn beaters
removed metal strap around motor housing then remove the 4 screws holding top motor cover on, then removed the 4 screws that hold gear cover in place, remove long gear that is driven by the motor gear, then with ring pliers remove ring off long drive shaft and lift off worm gears. once all gears are removed --removed all the old grease ( do this to get all the metal shavings out from the failed gear) repace the grease in the gear housing and reassemble in reverse order
Parts Used:
-
Barry from Rowland Heights, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
96 of 109 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Mixer speed was uncontrollable
Removed screw from back of mixer cover band and then removed the 4 side screws, lifted top off of mixer and removed screws from circuit board control switch, removing wires one at a time so as to install correctly. replaced screws in circuit board/control. Restored top of mixer replaced screws and the put cover band back on mixer.walla done
Parts Used:
-
James from Villa Rica, GA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
43 of 51 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!