KD220GDW3 Frigidaire Range - Instructions

Removed the baking element with a nutdriver. Slid it to the front of oven and removed the contacts on the back side. Installed the new element and installed the contacts at back of element. Slid it in the holes on back inside of oven and used a nutdriver to install the screws. It was very simple to do.

I just had to plug the new burner plate in the receptical
and it works again very well.

Removed the 2 element holding screws, disconnected the element leads & remover element. Replaced with new element.
All in all a real easy job (wish all repairs went this easy)
PartSelect had the element at the house within a couple days (Correct part I might add) which made the wife happy !!

First I removed the 2 screws on each side of the element and then pulled the element out, disconnected the 2 wires that were holding the element, got the new element and connected it to the wires, slid back into position, put the screws back in that hold the element and put the racks back in and turned on for test. It was so easy I had it done before my husband arrived home from work.

unplug old baking element using socket tool and put in new baking element - very simple and it works!

Took the back panel off. Removed the 2 screws from the old element,removed it. Put the new one in and replaced the screws. Put the back panel on done. What took the longest was cleaning behind there !!

Unscrewed back of oven the plate that was holding on old element, removed it (plugged into small wire device)
Plugged in new one and replaced screws to hold in place.

replaced it

1. First I pulled out the heating element from stovetop and removed old pan (no screws) very simple. 2. Put new pan in and inserted the heating element back in place.

Watching the video showed an easy, unscrew and screw back on process while connecting the wires back. It was really that simple. Once it was complete (not even 10mins), plugged it back in, and its been working great since.

The element pulls out easily and slides right back in and the drip bowls just lift in and out. TaDa !!

The meltdown was a spectacular event. After clearing the kitchen of smoke and allowing the oven to cool down. I easily removed the remnents of the old element by removing the screws holding each side in place and disconnected the two wires. I then insulated the hot side wire (red) to prevent the possibility of a short when resetting the breaker in order to use the stove top. The next day I found PartSelect.com and ordered the very reasonably priced new part with optional overnight shipping. it arrived at 1:00 pm the following day. Installation was a simple reverse of the removal. The oven works great and I now keep a fire extinguisher in my kitchen.

Turned off main power at electrical breaker. With pliers, removed two screws that hold element in place. Pulled element out about 3 to 4 inches. Disconnected two wires from element. With pliers, adjusted connections on new element connections from horizontal to vertical position. Connected two wires to connections of new element. Installed new element in oven with original two screws. Powered on main electrical breaker. Oven back in operation! Also, part arrived in 3 days! I'm a happy camper!

Moved stove out from wall and cabinets, then unplugged the stove. Removed the oven racks, then removed the 2 screws securing the baking (lower) element to the rear wall of the oven. Pulled the element out a few inches and disconnected it from the stove wires. Removed old element. Removed screws from rear panel to gain access to wiring. Inserted new element and connected to wiring. Put element in place and replaced the 2 screws in rear wall. Put rear panel back in place and replaced panel screws. Plugged stove back in and moved back into place. Tested oven and it worked just fine. Parts Select did a great job of filling my order and promptly shipping it. I got it in 2 working days.

I removed the two screws that hold the element in place. Then pulled the element out, disconnected the two wires. Reconnected the new elements wires, replaced the screws and the element was ready to go. Worked very well.