KBSD618ESS01 KitchenAid Refrigerator - Instructions

I did an internet search about the problem and found the information and experience that other people had. Ordered the part and that's it. One important thing to remember is to unplug the power supply of the appliance prior to making any repair. I short circuited the original board when I tried to plug it back in after cleaning the optics. (The board might have been bad before that.) The red light stop working but the frige is making ice non stop!!

Called a repairman out. For $125 he told me what I already knew! The ice maker wasn't working. Said I needed new emitter boards and ice maker. Would go back to the shop and call me with an estimate. Estimated parts were $330 plus another service call to put them in.
Went on line and found PartSelect. Emitter boards were $87+shipping. Ordered. Arrived in 3 days. 3 screws on each side. Unplugged old boards. Plugged in new. 15 minutes. Still did not work. Took out ice maker and examined. Gear that drives ice ejector fell off. End of shaft broken. Ordered new motor unit from PartSelect. $61+shipping. Arrived in 2 days. Loosened 1 nut screw. Slid ice maker out. Unplugged. Removed motor cover. 3 screws removed motor. Replaced with new motor and reassembled. 15-20 minutes max.
3 hours later had ice coming out for under $160. Wish I had known sooner. Thanks PartSelect.

Unpluged fridge, removed 3 screws from each control board (1 on left side and 1 on right side in freezer below ice maker compartment, unplugged and swopped out with new ones. Did one side then the other. Learned about the issue from other people on PartsSelect. Coulden't have been easier. Got parts in 2 days. Works like a charm now.

The emitter code: Hold the flap that covers the receiver. (On the left) If the emitter does not stay red, the emitter and receiver are defected.

Replaced the emitter and receiver board

Unplug the refrigerator:

I first removed the ice-maker service door by removing the 2 screws at the top. Next, I removed the 3 screws on the lift side that housed the receiver. It is close, so remove the 1 gold screws on the receiver. This will allow you to separate the switch without any damage. Plug the new receiver in and reverse the process. Put the gold screw in to secure the board. Replace the 3 screws back into the receiver panel.

Remove the 3 screws on the right side. The emitter has 2 gold screws. Remove them so I could separate the switch. Plug the new switch in and replace the 2 gold screws.
Place the 3 screws back into the right side panel.

This process took roughly 30 minutes. After assembly, the ice make was dropping ice in 30 minutes.

There are several large parts places in my area but I saved about $35 by ordering online.
I place my order on Friday morning and the part was in my hands Saturday @ 6: 30 PM the next day.




Oliver of Riverdale, Ga

Go first to Kitchenaid web site and download their consumer services Technical diagnostics on the ice maker. Very well written and clear to follow. Instructions step you through interpretation of blinking code lights which is key to finding the real problem and leads you to repair the correct failed part. My diagnosis said to replace both emitter and receiver. I replaced the emitter first and tried it and solved the problem I didn't need to buy the receiver but I have a spare part now. Do the diagnosis and save yourself some money. PartSelect got the parts to me quickly and saved me money compared to our local parts supply companies.

I did some research on the website and found out that there is a test with the sensor lights. When I looked at mine, they were not turning on or blinking when the door was openned.

The repair was very easy to accomplish and all I needed was a small philiips screwdriver. I unscrewed both left and right side panels covering the circuit boards and pulled the connector off. I'd say the most diffcult part was lining up the connectors to the boards since there's not a lot of room because of the harness length. Once the boards were connected, they set in place easy and I put the covers back on.

A word of warning, it took the system about ten minutes until the cycle started and water started filling the tray. But aside from that, everything is working perfectly well.

I saved about $200 in service fees!!

The ice maker would not fill with water. Water was available to in-door water dispenser. All signs pointed to the ice maker control boards. Ordered and replaced the boards. Within a couple hours it was making a new batch of ice every 30-60 minutes. The repair instruction video was a great help....made the repair a snap!

Removed old filter and installed new filter.

Replaced the light that was out.
Problem fixed

use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks

unscrerwed the broke part and screwed in the new one---5 minutes

The repair went just as simple as the video on the web site. Parts came really fast. replaced in less than 15 minutes. i thought the icemaker unit was the bad part but after gettin info from this site it told me waht to check first and i found that the emitter boards were bad. Thanks for saving me the money on buying the wrong parts. also bought parts the folowing week to repair my wifes kitchenaid mixer.

diagnosed the problem to be the emitter and receiver boards. replaced in about 15 minutes. works like new!

Followed the instruction video.

I had to remove ice storage compartment sitting above motor on door to expose auger gear. Then used a small socket to remove 4 screws from underside of auger motor compartment in door. Motor drops out with a small wiring harness attached. This simply unplugs and then swaps in with new motor. Auger axel was sanded to remove rust and grease applied. Motor door and ice compartment were then reattached.