KBLC36MHW01 KitchenAid Refrigerator - Instructions

I Removed 3 screws, pulled off the plate and put the new one on, screwed in 3 screws and away I went. I could not believe how easy it was to order the part and how quickly it arrived. I was very pleased. And I was literally screaming with excitement when I heard the first set of ice cubes drop!

Very simple fix, remove 3 screws, two connectors to the old switch

I removed the two attachment screws and lifted the old icemaker out and disconnected the plug. The new one was identical to the old one so the installation was just a reversal of the removal. The water soleniod was sticking from not being used so I took it apart and cleaned it. The next morning I had ice. The part arrived at my door in less than 24 hours from my order placement.

I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.

Wathced video (VERY helpful)of how to do repair to make sure it was within my capabilities to do. Made sure I had all requested numbers before ordering. Replacement part was an EXACT fit. 15 minutes of work and I saved nearly $150 of estimate by local service company. I am (and will continue to be) a repeat customer. Thanks. Mel

Checked compressor with amp meter, and found it was not running, found Overload Switch bad.
When removing old switch watch carefully which lug you move wires from, so you will know which
lug to put the new switch on.

BE SURE YOU KNOW SOMETHING ABOUT
ELECTRICITY!!

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!

I replaced the defrost relay folling instructions I read on the internet--and it still didn't work--So I replaced the compressor start relay which was easier than the defrost relay--it worked and the fridg is working good.

We followed the video on the KitchenAid website. We turned off water valve at the wall, unplugged the refrigerator, removed the old icemaker by unscrewing the three mounting screws. We unplugged old icemaker from electrical source at back of refrigerator freezer compartment and removed it. We detached the on/off bar from the old icemaker and installed it on the new icemaker. The new icemaker fit perfectly. We plugged in the electric wire to the existing power cord at the back of the refrigerator freezer compartment. We placed the new icemaker in the same position as the old, making sure the mounting screw holes were aligned. Plugged refrigerator back in and turned on the water. Works beautifully.

It actually took me longer to think about the repair than actually doing it. It was three screws, two upper that you just loosen and then one on the bottom that you remove. Pulled the unit out and disconnected the power. Slipped the new unit onto the two upper brackets, after connecting the power cord, tightened the bracket screws, reattached the bottom set screw and I was making ice. Incredibly easy. When I ordered the replacement unit they said it would arrive in 3-5 days, but it only took a day and a half. Great experience all the way through. I'm a customer for life.

put arm up to stop icemaker from creating new ice cubes. us nut driver to unscrew 3 of the nuts holding icemaker in place do not completely remove the 2 top screws. lift off the screws and unplug from inside wire connection...make sure water tub is removed and frig unplugged. clean off ice anywhere inside freezer...take out new icemaker and connect wire plug...attach icemaker on to the 2 top screws...use nut driver to tighten into place. add and tighten bottom screw...leave arm down...replace clean and dried water tube into back and make sure it slid into ice maker...tighten screws in back and attatch water hose to tube...plug frid back on slide back into place...will start making ice in an hr or so....

Replaced the control of the ice maker assembly.

First I turned off water supply. Then removed the two screws that attach ice maker, then disconnected the wiring harness.

Attached new ice maker in reverse order.

I loosened the two screws on which the ice makers hangs and removed the third screw toward the back. I lifted the icemaker a bit and removed the part and unplugged the unit at rear. I reversed the process to install the new one. All very simple.

At first nothing happened, no water filling the tray. I thought there must be some other problem. A few hours later I heard ice being dumped into the ice container. I don't understand the delay but it works fine.



At first no

I removed the icemaker. One screw at the bottom and then unplug the electric. Remove the old motor from the face that has 3 screws holding it. Put the new motor in. A very simple job. I now have a full ice bin by the next morning.