JVM152JC General Electric Microwave - Instructions

Used the putty knife to pry open the inside of the door, just like another gentleman did, that I read on this web site. Used the phillips head screw driver to remove the broken pieces left on the door, and replace with the new handle. Popped the back of the door in place, and finished. Very simple. Saved about $400. Love it when a plan comes together.

Followed suggestion by previous poster to remove bottom panel...facilitated process well

First, unplug microwave. Unscrew two screws at top of microwave, slide grill cover left and remove. This allows access to single screw holding control panel. Remove this screw and lift up control panel to remove. Secondary door switch is black switch at lowest position. The switch is held in place by a lever in back and very hard to get to. Remove the wires plugged into the switch, then remove two screws holding the plastic switch mount that holds all three switches. These screws use a "star" type screwdriver. Once the plastic mount is free, lift it up, right, and tip it slightly to find the lever that will release the black secondary door switch (the lowest switch)...release the broken switch, snap the new switch in its place. Replace the plastic mount by lifting and replacing back into position and replace the two "star" screws. Now, replace the wires onto the new switch, and test operation. Replace control panel, and top grill. It goes faster than it writes...getting the old switch out through that difficult to reach lever was the hardest part...still less than thirty minutes.

Changing 2 lightbulbs is NOT ROCKRT SCIENCE. With a screw-driver, remove the under MW light lens, unscrew the 2 burned out light bulbs, and replace with 2 new quality light bulbs. Test out that both are lite and working as they should, replace the lens and you are done, Until you find out one of the new (made in Chins) light bulbs is burned out after about 6 hours of being lite, call the parts phonr number and order a new replace bulb.

Because the microwave is old and the bulbs, I believe, had never been changed I carefully tried to unscrew the bulb. However, when I went to unscrew the bulbs the end of the bulb broke off and remained in the socket. I used a few different tools then remembered that sometimes a raw potatoe can be used to unscrew the remainder of the bulb, but to no avail. Finally had to unscrew the whole underside of the microwave to remove the broken bulb. May I suggest that you have the socket face away from the wall to screw in the bulb instead of the socket pointing toward the wall. You need to know yoga just to manuver the bulb into the socket.

I took instant pictures at each step to make sure I put the wires back correctly. Removed the front panel. Discharged the capacitor with a voltage meter. Removed parts in front of the magnetron. Removed and replaced the magnetron. Reassembled. Works find now. Small hands, a flashlight and a magnet (for dropped screws) would help. I did not need the pictures.

Watched How to repair a Microwave that turns on when the door is opened Video on the web. From this took a shot at the switch was the problem. When I removed the switch it was defective. The small button was in and when you turned the switch upside down the button would drop back into position. Ordered a switch for $25.oo , installed it and the microwave is working fine.

used small screwdrivers to insert behind black door hickey. pried it loose, undid screwa to old handle and SAVED them to put in new handle. Relatively easy.

My son had to replace the bulbs because the screw that holds the bulb shield was so tight that I couldn't remove it. It was too difficult for me to do it myself.

Remove light cover. Replace bulbs Note. Light bulbs are 40W,Too much heat for bulbs & sockets

It was a snap using the instructions given. The key is getting into the unit. I did have to use a multimeter to find the failed switch since there are two of that type.

I removed light bulb cover shield,took out defective bulbs and replaced with new ones. 5minute repair

We separated the inside of the microwave door from the outside in order to get to the screws. This was the most difficult part of the repair. We got the directions on how to do this from the internet. We did not find the screws too long because there were spacers with the original screws. We found the top spacer put in backwards because the original screws were shorter. After putting the spacer in correctly the screws that came with new part were fine.

Pried off the inside of the cover, removed the broken handle with ease. When I went to screw in the new handle, I couldn't get the new screws to tighten. Turned out they were too long, so I had to use the screws from the old handle. After I figured that out, I was finished rather quickly.

took the inside strip off the door with a thin knife, then removed the screws from old handle parts left on door. took a little while to tighten the toop screew, which I had to leave loose. it works and looks very good.