JS48SSDUDE00 Jenn-Air Refrigerator - Instructions

Unplug fridge, turn off water to fridge
Uninstall ice maker (some tools needed)
Remove ice buildup inside water line

Purchase new ice maker and installed it while watching a youtube video of how to do it. Once installed, turned on the water line and plugged in fridge.

Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.

Removed old ejector arm and installed new part.

I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.

Just needed to replace the water filter

I took the cover off, and noticed the tabs holding the timer wheel were broken off on one side. after removing the wheel, I noticed the shaft from the ice lifters was broken. Since the only way I could repair it was to buy the entire module, which I did. I received my part in 3 days. When it came, I began removing the old module by taking out the three screws holding it. After replacing the module which took about 10 minutes, my machine was making ice within about an hour. My ice holder was full in 3 days. Albert Moran, Milton, Fl

Over the last several years we have had several appliance repairmen try to fix the icemaker. One replaced the entire icemaker. We bought a booster pump for the water. After spending about $1,000 over the past few years trying to fix the problem, a plumber doing routine plumbing work looked at it, and said it might be the control board. I found instructions online how to test the control boards. I ran the test, and they failed. I ordered the parts from PartSelect, followed their easy instructions, and tested the new units. They passed with flying colors. We now actually have an automatic icemaker for the first time in years.

diagnosed the problem to be the emitter and receiver boards. replaced in about 15 minutes. works like new!

I replaced the Electronic control boards because the indicator lights were letting me know that there was a problem, but!!!! when that did not fix the problem, I took the ice maker out and removed the control module from the end of the icemaker only to find out that water had gotten in there and corroded the electronic contacts... this may have been why the indicator lights were not working on the emitter and receiver. I was going to purchase just the module, but the entire ice tray was beginning to de-laminate and plastic was flaking off all over. To make a long story somewhat shorter, I purchased a new icemaker and it works fine... one caution though... My icemaker did not come with any information that told me I had to flip the icemaker to the "on" position from vacation mode by inserting a screwdriver in the back of the module inside of a small white ring. This hole is where the shut off arm WOULD go if my model had one.

I went online and watched a U-tube video that said it was most likely the electronic emitter and receiver boards and showed how to replace them. I first unplugged the appliance (just to be safe) then, I unscrewed the screws holding the faceplate on. The board simply has a plug which you unplug with a little care and effort. I then plugged in the new board, resituated it into the hole and screwed the faceplate back on. You simply do the same for the other board on the other side. Viola! Lots and lots of ice!! The guy at sears said I shouldn't do work on such a complex appliance. Probably because I am a woman! Anyone can do this job! Winning!

My icemaker quit 3 years back and at that time I searched for do-it yourself repair books with no success. I found this parts place web site and people having the same problems as myself. I purchased the parts as others have and problem solved! Ice all the time, woo hoo!

After unplugging refrigerator, removed emitter and receiver cover plates on each side of freezer unit (3 screws each) and mounting screws for circuit boards. Unplugged old boards and plugged in new ones and reinstalled boards and then cover plates. Although, indicator code lights seem to still indicate a problem, ice maker has resumed operating after 24 hr.

We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing

Put One card in one side and other card on the opposite side, push in on both sides to press in clips that hold light in. Once clips are in light will start to come out unplug light and plug in new light. Push light back in.

Removed 4 bottom screws. Removed module screws. Replaced module and motor with new parts (came assembled). Replaced module screws and installed the ice maker with the 4 bottom screws.