JS48PPDUDB13 Jenn-Air Refrigerator - Instructions

Do not try to pull out the water filter by the cap. There is a button that releases the filter so you will not have to replace the cap. The cap twists onto the filter. When replacing the filter, the cap goes onto the new one.

Unpluged fridge, removed 3 screws from each control board (1 on left side and 1 on right side in freezer below ice maker compartment, unplugged and swopped out with new ones. Did one side then the other. Learned about the issue from other people on PartsSelect. Coulden't have been easier. Got parts in 2 days. Works like a charm now.

I pushed the lever on the filter located at the bottom of the refrigerator and it popped out.

followed the video provided on website. repair was very simple / straight forward. Once emitter and receiver boards were replaced, issue with ice maker was resolved.

filter has to be removed and attached then inserted into rifrigerator

Very simple fix, remove 3 screws, two connectors to the old switch

Originally I took the module off and found that a small plastic part had broken. Both pieces were still there, so I super glued them together and reassembled the unit. It worked great for a couple months. I realized it needed a more permanent fix, so I found the model # and looked up the part. That was very easy on your website. I ordered the part expecting it to take 4-7 days. It was at my house in two days! 15 minutes later I was makin' ice, and makin' my wife happy. Thank you for an all around great experience. I'll definitely buy from you again.

The holder is held in place with two screws. Once you have it unscrewed you can snap the old sockets out and replace them.

Ordered new sockets and presto, the lights work again.
They just snapped into the holder and the holder went up with two screws.
HINT: I did take a photo of the 4 electrical connectors AND labeled each one with a Sharpie 1, 2, 3, and 4 from left to right.

Called a repairman out. For $125 he told me what I already knew! The ice maker wasn't working. Said I needed new emitter boards and ice maker. Would go back to the shop and call me with an estimate. Estimated parts were $330 plus another service call to put them in.
Went on line and found PartSelect. Emitter boards were $87+shipping. Ordered. Arrived in 3 days. 3 screws on each side. Unplugged old boards. Plugged in new. 15 minutes. Still did not work. Took out ice maker and examined. Gear that drives ice ejector fell off. End of shaft broken. Ordered new motor unit from PartSelect. $61+shipping. Arrived in 2 days. Loosened 1 nut screw. Slid ice maker out. Unplugged. Removed motor cover. 3 screws removed motor. Replaced with new motor and reassembled. 15-20 minutes max.
3 hours later had ice coming out for under $160. Wish I had known sooner. Thanks PartSelect.

With the freezer door closed, remove 4 screws around the ice maker door assembly. Open the freezer door and remove about a dozen small flat-head screws around the sides of the door that hold the stainless steel cover to the freezer door. No need to remove the very bottom screws if you have something to support the cover with. Remover 4 hex-head screws that hold the ice/water dispenser control pad in place, use tape to secure this pad to the freezer door so you don't have to undue all the electrical connections. Remove two screws that hold the Ice Door Motor & Bracket Assembly in place - disconnect the electrical connection for the assembly. Replace the new assembly in the opposite order it was taken off. Presto - done.

Bought new applicator

Just needed to replace the water filter

Removed the cover plates and unplugged bad boards. Hard to plug in boards after attached to cover plates. Plug in boards first then attach to mounts. Ice in 4 hours.

Easy repair. Remove 2 hex bolts. And remove.Install Bracket and replace 2 hex bolts and reinstall ice maker door to bracket. 10 minute repair.

I just removed the unit and replaced the mold/'heater with the new one and re-installed. It was very easy and didn't have to turn off the refer. or empty the frozen food.
However , there were not instruction that came with the mold/heater unit. I had no problem but other do-in-uselfers may need some basic instructons
Jim