JS48CXDBDB00 Jenn-Air Refrigerator - Instructions

Just replaced the switch, but unfortunately that was not the problem; nor was it the bulb....so I am back to square one.
But Parts Select is a great place to order from. Thank you.

Repairing a refrigerator is inimidating to say the least. Our ice maker has broke twice in the two years that we have owned it. The first time we had a service repair faciliting come out and they replaced it for about $200. The second time I had no idea what the problem was until I came to this repair forum. I soon realized that the electronic control boards needed to be replaced. Received the part two days after ordering and it took all of about 5 minutes to unscrew the old boards, pop them out, and put in the new ones.

Love your website and the money that you saved me!!! Thanks a million!

power off, 3 phillips head screws on either side of freezer. unplg each board, plug new ones in completely. ( cannot mix them up, size difference) replace screws and enjoy ice cold beverages once again!!!!!!!!!

Received the union I ordered, then discovered that the tubes were different sizes, so I had the wrong part. I had read elsewhere that it was necessary to trim the two ends of the tubes with a box cutter to stop the leaks - I did this, and the leaking stopped. I was then able to go to a local hardware store and get a 5/16 to 1/4 union and replace it. The leaking is stopped, and the water supply in the door is now working like new. No problem with partselect, but I did buy a caliper so that I can check tube diameters if I ever have a similar problem! This is a great site to find instructions - well worth the time to search!

I wasn't sure what the problem was, but the ice maker seemed simple and on-line resources suggested the control and motor assemblty was at fault. I searched the internet and Partsource had great diagrams which I could match to the part in hand. The price was right (way less than the local stores) so I ordered it.
I unplugged the unit from the power in the freezer, but unplugging the entire refrigerator works too. I pried off the white cover on the front of the ice maker, which snaps in place top and bottom. There are three screws holding the contoller (the entire front piece), remove them, pull off the controller and push the new one in place. You may have to turn the blade shaft to line up the notch on the shaft to the motor. Then reinstall the three screws, The screws go into plastic so it is easy to cross thread them, so be careful, I actually think I did with no ill effects. Snap on the cover and repower the unit. Done. Simple and quick.

Icecubes came out half-way, and refrooze. I figured out, that the melter does not work (HEATER in the icemaker) Voltage measured 105V no load. Studied the Internet, and folloved an advice: shorted the back wire and the blackwire with white stripes.these go to relay contacts. It seems, that the relay contacts are no good on Infrared receiver boaed. I turn off manually the icemaker, when needed

I removed the cardboard back then using a nut driver removed the three mounting screws, removed the old fan/motor and installed the new one, installing the three screws and replacing the cardboard cover.

My big problem was getting the right parts. Don't ever order refrigerator parts using the refrigerator model number. I did and got the wrong part, sent it back and talked to the parts lady and ordered again describing the error, the needed parts shape etc and she sent me the exact part I had sent back. I sent it back and removed the fan motor to get the part number, called and ordered by number and got the right one. Hallelujah!

removed old bracket and replaced with new one - two screws and it was done - simple

Being too lazy to pull out the refrigerator out and unplug it, I turned it off at the fuse box. Opened the freezer door and unscrewed the three screws holding the sensor. Pulled the sensor out and unscrewed the board then unpluged it and removed it. Plugged in new board, screwed it in then replaced the three screws. Repeat on the other side. The most difficult part was getting to one of three screws on each side; it almost required a third hand to hold the flap door between the ice maker and the bin, while removing said screw. I must at say that this product is definitely over engineered.

The ice mold has a coating on it. Over time the coating deteriorates. If your ice maker leaks water into the ice reservoir inspect the mold to see if the coating is compromised. If so, replace with new.

Remove the ice maker assembly. 3 small hex screws. Unplug power cord. Disassemble ice maker assembly. Remove ice mold/heater. Replace with new. Reassemble.

Looking at the ice maker it is pretty cut & dried as to how to remove the unit. I took out the ice tray and just started removing all the mounting screws. The same for the mold ice tray & heating element. I was just sad that you did not have just the heating element separate from the mold ice tray.

I removed the cap from the filter pushed a lever and removed fliter. I replaced the old filter, removed the caps on the new one and slid it into channel after replacing the outer cap. I removed water from the spigot for 4 mins. and it was ready to go. I pushed the reset button to get the green light to come on.

It was so easy!

Thanks for the rush to my home on the part.

I just unscrewed the plate that locks in the light switch (screwdriver) and unplugged the old faulty part and plugged in the new switch, screwed the cover back on and I was done!

Easy!

And I am not Mr. Fix-it!

Had to disassemble ice maker to install part. . .

Just put the new one in.