This part is a replacement halogen lamp for your oven. The bulb is 25 watts and 120 volts. If your light bulb is burned out, this is the part that replaces it. Be sure to turn off power to your range ...
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
Keep your oven safe and functional with this replacement interior door glass, the heat-resistant panel that lines the inside of your oven door. With dimensions of approximately 20 5/8" x 13 1/8", it f...
Need a fix for your Whirlpool stove, oven, or range? We've got the perfect solution ? our genuine, OEM Tangential Fan. This fan plays an essential role in maintaining optimal cooling inside your appli...
This part is the replacement hinge bracket for your microwave. It is made of metal and is approximately 8 inches long and 1 inch wide. The hinge bracket can also be known as the door hinge receiver or...
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Joe
December 7, 2019
Power was out for approx. 1 hour, power back on, but not power or lights to oven working. Entire display panel is blank, and oven does not work?
For model number JMW9530DAS
Hello Joe and thanks for writing.
Power unit down by turning off the circuit breaker(s) for one (1) minute.
Power unit up by turning on the circuit breaker(s).
.if that fails you might have a damaged terminal # PS11750972. Check and replace if needed. We hope this helps. Please contact us anytime.
1 personfound this helpful.
Was this helpful?
Thank you for voting!
Daren
January 18, 2020
Stove won’t work and panel said fault detected-it wont let me cancel or enter like the scrolling message says. Any idea?
For model number JMW9530DAS
Hello and thank you for writing.
We suggest to try a hard reset:
Go to your breaker box and shut the breakers for your unit off, wait 5 minutes and then turn the breaker to on again. That should hopefully clear this problem.
We hope this helps. Please contact us anytime if you require further assistance.
Was this helpful?
Thank you for voting!
Karl
September 7, 2021
Oven touchpad has power but when the key is pressed it just beeps and does nothing else. I am assuming its not the terminal since it has power. Any ideas?
For model number JMW9530DAS
Hello Karl, Thank you for the question. This is normally an indication the Convection Electronic Control is defective. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
This is fairly easy for anyone to do. First I opened up the front (silver part) of the oven door by removing the screws at the top and the bottom. Then I kept on removing the various layers of glass... the 2 outside ones are removed by removing their respective screws and then you get to the inner-most. These 2 inner ones are in a frame that holds them together. I removed the large silver frame that holds the insulation and the 2-glass-frame in it. Just remove the screws and then tilt the insulation frame out a bit to remove the glass frame. You can tilt the entire insulation holder out but the insulation is soft and it starts to fall off. Just tilting it enough worked for me. Then I opened up the glass frame from one end, removed the left-over broken piece of the old glass pane and installed the new one in. Then reassemble. The entire process is very easy - but you will need another person for a few minutes when you remove /reinstall the glass frame inside the insulation holder. You would just need a little help holding everything... nothing technical. I would rate the repair technicality at 4 or 5/10. It could even be a 3 if there were less steps involved. Good luck! By the way, Amana/Maytag wanted $70 or so for the glass and then the repair fee. I got the part here for about $50.
removed oven door, removed screws from bottom and sided, door is in layers, removed door layers like taking apart a sanwhich layer by layer, once i got to the inner layer i just had to bend out the little tab on the frame,remove the broken pane and place in the new one, bend the tab back and then put the door back together layer by layer, it was very easy and saved me money, and frustration in dealing with a repair man from a well known company who tried to tell me I needed to replace the whole door as the glass was factory sealed in the door, WELL! this girl's hair may be blonde but not that blonde, I received the glass the very next day, and it took me 40 minutes tops to replace the glass, EASY! KC
.gif "MICROWAVE Diagram and Parts List for Jenn-Air Microwave Oven Combo")
