JMP28BC1WH General Electric Range - Instructions

GAIL from STREAMWOOD, IL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

welded supports for the surface elements were broken

unplugged the broken elements and plugged in the new ones. Took about one minute. Tools used: hands and fingers.

Parts Used:

Surface Element - 6 Inch - 240V

Thomas from Montgomery,, AL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Burner wouldnt heat

Watched video,and used it as guideline.Biggest problem was removing tape from old wires.

Parts Used:

Mary from Leon, KS
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Burn box had rusted through under one burner.

With a nut driver removed the four heating element sockets (four small sheet metal screws) and the seventeen sheet metal screws that secured the burn box, removed the sheet metal box and inserted the new one. Not all the holes lined up at first for the screws, but starting in front with the four that did fit, the sheet metal gradually lined itself up with all the other holes for a perfect fit.

Parts Used:

Range Bottom Burn Box

John from Belle Plaine, MN
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers

Was this instruction helpful to you?

The range kept giving an F2 alarm

When I got the part I removed the tin cover (two screws)on the back of the range. I removed the sensor by removing the two screws inside the oven and pulled out the sensor. taking the instructions advise, I checked the sensor with my ohm meter and although it read 1.1 ohms as compared with the recommended 1.09 ohms at room temperature in the instructions, went ahead and changed the unit. The connector did not fit my particular model so I spliced the wiring and using the two included wire nuts made the connection. I reinstalled the sensor, reattached the gas line, plugged it in and tried the oven before I put it back in place. The oven works great now and it was super easy.

Parts Used:

Oven Sensor

Les from Coal Creek, CO
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set

Was this instruction helpful to you?

GE Electric Range rear left burner quit coming on

Removed the back top cover with 1/4" nutdriver. Removed the burner terminal block with 1/4" nutdriver. Within 15 minutes had the terminal block kit removed and installed and in service.

Parts Used:

Richard from Richmond, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers

Was this instruction helpful to you?

Needed to replace drip bowls

Husband just snapped in place in about 8 seconds! Thanks for the fast delivery and pleasant staff assistant.

Parts Used:

Gloria from Dallas, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

No Problems

I removes the old element and drip bowl, then replaced the drip bowl, then replaced with the new element. Approximatly 3 minutes. . .

Parts Used:

Surface Element - 8 Inch - 2350W

Jerry from Copperas Cove, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

needed new drip bowls for stovetop GE

removed the burners and dropped the drip bowls in. Very easy to do,

Parts Used:

Patricia from Centereach, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

surface element not working

I simply pulled the old surface burner out, and plugged the new one in. It took less than one minute! The amazing part of this repair, is actually that PartSelect sent the replacement surface element burner OVERNIGHT! I could not believe it, and was VERY impressed with their commitment to help their customers in time of crisis. It arrived just on time for my Thanksgiving not to become a nightmare. Thank you PartSeclect!

Parts Used:

Surface Element - 8 Inch - 2350W

Claudine from The Colony, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

My drip bowls were rusted and corroded

I ordered new drip bowls and put them in place. They fit just fine.

Parts Used:

Glenda L from Lake Placid, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

needed new drip pans-

replaced pans- what I would like to comment on is the time- I ordered one day at noon and had them the next day at noon- I live in tiny town on northern border of USA- it was awesome- I couldn't believe it was them- 24 hours- super job and excellent price too

Parts Used:

Connice from Massena, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Drip Bowels badly stained.

Unplug heating elements and pick up drip bowels and reinstall elements.

Parts Used:

Dean from Hill, NH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Front and back burners not getting hot

Followed the video supplied with the email on the parts order form. Biggest problem was pulling the range out from the wall, the repairs went without a hitch. The PartsSelect video was a great help showing the short cut to getting the new wires in by using the old wires as a pull wire.

Parts Used:

Fred from De Leon, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

Was this instruction helpful to you?

plastic adapter was broken on end of the block kit

unplugged old block from both sides, ran new wire and plugged new wire to both ends and presto it worked, thanks for making it easy to fix. Thanks- Michael J Dumas

Parts Used: