JMP28BA2AD General Electric Range - Instructions

I read the previous repair stories and figured it couldn't be that tough. Mine actually had a slight deviation and I'm sure based on model...
To remove the oven door handle, I had to remove 3 screws (phillips) on the top of the hinged door. This allowed the face plate to easily pull away from the inside of the door. The existing handles were held in place by a single hex head screw each.
Voila, in 2 minutes the entire handle was off.
This is where things had a slight deviation.
The door end caps I bought had 2 alignment prongs that extended beyond the actual surface. My door did not have holes for them to go into. No big deal, I took some wire snippers and clipped the little plastic prongs off so it was flush like my old ones. That took about 3 minutes because I had to go back into the garage to get the tool :-)
My metal door handle bar did not want to go all the way in very easily into the end caps. I went back into the garage and got some WD40 and sprayed into all pieces and wiggled things back and forth for a few minutes, placing it against the oven a couple of times to ensure I had the bar was seated enough where the holes lined up with the oven.
I would recommend putting the end caps on the bar PRIOR to attaching one side to the oven. I originally did not do this and when it was difficult to get the bar on, I had to take it off so I could perform the procedure I just mentioned.
Honestly, the entire "job" took 10 minutes.

I ordered the replacement clips from this site and they arrived in a timely manner. The clips were perfect, but due to the age of the oven, the holes had elongated and the new clips kept falling out also. I modified the clips by widening the tips with a pair of pliers. They are holding just fine. I don't think the older clips could've withstood the modification.

Very simple to replace, pull off the old element and push in the new one. Not only was it super easy, part select was so easy to work with. I had placed the order wrong, and immediately called customer service. They cancelled my order and placed the new one, refunding my money within 2 business days for the wrong order. Courteous, friendly and prompt. I would highly recommend them! Oh, I forgot to mention that the parts actually fit perfectly, unlike drip pans bought elsewhere. Thank you, Sincerely, Cindy

1) TURNED OFF THE POWER TO THE OVEN. 2) REMOVED THE TOP DOOR AND RACKS. 3) REMOVED THE 2- 1/4 HEAD HEX NUTS AND PULLED THE ELEMENT FORWARD ENOUGH TO EXPOSE THE ELECTRICAL CLIPS TO THE ELEMENT. REMOVED THE CLIPS WITH A PAIR OF NEEDLE NOSE AS ADDED GRIP. 4) PUT THE WIRE CLIPS ON THE NEW ELEMENT AND REVERSED THE ABOVE PROCEDURES.

took old unit and measured it part select made it easy for me ordered new unit and installed easily and quick thanks to quick service and shipping

All I had to do was pop the clamp on the top part of the heating element and push the clamp into the hole.

Unplugged the Range and removed the two screws holding down the cook top. You do not need to remove the vent chamber at the rear of the range since the top lifts up about 4 inches. This should be enough room to get your hand onto the plug going to the door switch. Pull off the plug and remove the swich. Pop in the new one, put on the plug, reinstall the two screws and you are done!

Read the thread on "burnt smell" and DO NOT assume it is a burned out element. Follow your nose!!

[1] squirted LiquidWrench on the 4 screws holding the convection fanblade rear cover in place. Used a socket and rachet to remove screws; the loosener really helped after 10+ years.

[2] the broken heating element was easy to remove. The two spade connectors however didn't have much free length;these wires wanted to retreat back into the rear oven wall.
[3] So i put a small binder clip from my desk supplies on each spade end, this left the connectors where I could grab them.
[4]I used needle-nose pliers to firmly crimp the the spade connectors onto the new heating element; couldn't have made a firm placement with fingertip pressure alone.
[5] I cleaned the oven door hinge area, oven bulb area, and other hard to reach spots with Simple Green and wipes.

Removed old surface burners and replaced them by plugging in the new surface burners. Now they work GREAT! Parts ordered and received with-in 3 business days. Fed EX delivered parts in good order very quickly. We recommend PartSelect.com

Although the parts did fit, some modification was needed to remove the excess tabs as it appears these parts were for multiple applications. However the end result was a good fit and reapirs were successful.

I carefully removed the burners, removed the bowls and replaced them with the new ones. Easy as pie!

Removed existing surface element and replaced with new element.

P.S.

Part Select service was excellent.

Nothing to it. Took off the old ones and put on the new! Tada - new stove!!

I removed the control panel by removing 7 screws and replaced the light indicator and lens.

Had to take back off of the door to get to screw that held the broken piece of handle before installing the new part. Then had to put the back on the door and slip the door into place.