JM250DF1WW General Electric Range - Instructions

Susan from Alpena, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

plastic adapter was broken on end of the block kit

unplugged old block from both sides, ran new wire and plugged new wire to both ends and presto it worked, thanks for making it easy to fix. Thanks- Michael J Dumas

Parts Used:

Surface Burner Terminal Block Kit

Michael from West Monroe, LA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers, Wrench (Adjustable)

Was this instruction helpful to you?

Large eye would over heat when was on med. settings

I unpluged the stove pulled it out and took the 6 screws off the back to get to the switch. Around front take knob off and removed the two screws holding the swich in place and pulled it out the back. Pulled one wire at a time off of the old switch and replace on the new switch. Nothing to it had it done in just a few mins.

Parts Used:

LEE from ROME, GA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

burner switch needed replacing

replaced wire for wire

Parts Used:

Surface Burner Terminal Block Kit

daniel from norwalk, CT
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Burner would not turn off

The burner light did not turn off, and the rear burner stayed hot. Unplugged unit and removed switch, which turned off the "burner lit" lamp. Thus I figured it was the switch that was causing the problem. Ordered the switch (I think around $18 and plugged it in. I think there were 4 screws to get the panel off, and then another 2 to get the switch off. When I plugged the unit back in (it had been unplugged while I waited for the part to ship) it beeped for a while. I had to turn the breaker on and off, and that solved the beeping problem.

Parts Used:

Thomas from Winter Garden, FL
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

Was this instruction helpful to you?

The 8" burner switch heated burner to high Temp

Went online looked up model no and found Part No. and ordered it couple of days It came in mail Cut power to oven took knob off two screws back panel. wired new switch like the old one replced thwe switch and two screws and panel connected the power tried new switch it worked great.

Parts Used:

Randy from Ellenboro, NC
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers, Screw drivers

Was this instruction helpful to you?

The burner combusted burning the the burner switch

Disconnected the appliacnce from the power source. Using screwdriver, removed the back panel and disconnected every wire that are connected to the switch. Pulled out the front nob and removed the switch. Then install the new switch by screwing it back in. Place all wires back and back panel. Connect and finish.

Parts Used:

Felipe from Donna, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Disgusting looking burner drip bowls.

Just had to change out the drip bowls, easy. But, I wanted to comment on the quick delivery on the new bowls. I was impressed. Thank you.

Parts Used:

Constance L from Woodhull, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

none

Took the old pans out and put the new ones in. Simple as pie

Parts Used:

Leslie N from Carson City, NV
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

dirty bowls

used my hands to remove heating element, then remove drip bowls, then install new bowls, then install heating elements, done!!!!!

Parts Used:

Richard from Bainbridge, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Rusted out burnner bolws

Remove old burnner bolws and install new ones

Parts Used:

charles from ft.pierce, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

My drip bowls were rusted and corroded

I ordered new drip bowls and put them in place. They fit just fine.

Parts Used:

Glenda L from Lake Placid, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

needed new drip pans-

replaced pans- what I would like to comment on is the time- I ordered one day at noon and had them the next day at noon- I live in tiny town on northern border of USA- it was awesome- I couldn't believe it was them- 24 hours- super job and excellent price too

Parts Used:

Connice from Massena, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Drip Bowels badly stained.

Unplug heating elements and pick up drip bowels and reinstall elements.

Parts Used: