JJW8530CAS Jenn-Air Wall Oven - Instructions

Removed 4 screws that hold the clock assembly panel in place. Removed the defective part and replaced it with the new part. The wiring connectors were almost impossible to incorrectly connect.
Easy and saved $ 100

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

Removed two screws, unplugged the old unit, plugged in the new, screwed the new in. Job done. Would have been less than five minutes if I hadn't kept dropping the screws.

Our oven quit working again. I called the repair(dealer) man and he said we needed a new control panel. It would cost $180.00 and labor would be $60. The total repair would be $240.00. We considered just purchasing a new one. It is a slide-in range and they start at about $1500. So I began looking for a control panel on line. I found your web site and entered what was wrong with the oven. Your site suggested we try replacing the oven sensor. There was a video that showed how simple the repair was. We ordered the part. It came quickly and I immediately made the repair (about 10 min). I was very disappointed that it did not work. I went back to you web site and tried the next option. It was a terminal block for only $20.00. I didn't even know what a terminal block was, what it looked like or where on the range to find it. But I went again to your video and I learned quickly what to do. I ordered the part and it came in two days. I made the repair in about 15 min. My wife was very happy that the repair worked. Our total cost was about $80. The $240 quote would not have fixed the oven anyway. The repairman was wrong. I was very happy with the results and the money we saved.. Good Job PartSelect and thanks.

My friend actually replaced this but it was really quick and easy. If I'd had to do it myself, I think I could have because it came with the simpilist step-by-step directions! The best part of all was that I ordered it online on Monday and had it on Tuesday....during Christmas week!! Unbelievable service. Will definitely recommend this company to anyone needing any appliance parts!

It was nice to be able to find this site and see that my problem was the same as others and they had all solved it with replacing the control module. So I ordered the part. Received it. Removed the 4 screws on the panel, then removed the connectors, then removed the bolts holding the control panel on the board. Replaced control panel and hooked it all back up. Very easy and was working in 15 minutes.

I followed other postings about this repair. It was easy. Open oven door, remove 4 screws that secure oven in the cabinet. Slide oven out a few inches. I thought it would be too heavy for me, but it wasn't. Remove 4 screws along the underside of where the clock panel sits. Have the oven door open, look up and you will see the four screws. Lift up and off for the glass front of the clock area. Undo the 4 sets of wire connections. They just snap in and out. Lay the glass on a towel, remove the clock assembly with a nut driver, replace with new clock assembly and reverse the instructions. When putting the glass panel back on, make sure you hook it over the top ledge. I missed that and after I replaced the 4 screws, I realized the top was not secure. Don't forget to kill the circuit breaker while working on this.

The display belongs to the convection oven. We still could use the oven because we knew how all the buttons and beeps worked, but we replaced the control module because we couldn't sell the house without it. Here's how to replace the module:
- Remove the bezel on the microwave above the oven (4 screws on the sides).
- Now you can remove four up-facing screws on top of the control panel. Don't unwire the panel, just lay it face-down on the topmost oven shelf, as one of the others above advised.
- Looking at the back of the clock module, remove the two connectors. The larger one is difficult to pull. Just force each end gently straight up with a flat screwdriver.
- Remove the screws holding the clock in place. They're at the two ends.
- Swap the clocks and put everything back.
I bought this module from PartSelect because of all the customer feedback you see here. It gave me the confidence to do it myself.

We followed the 63 year old lady's repair directions found on this website and were able to install the new display board in less than 15 minutes. As she said, it was really easy!

I unscrewed the cover on the oven. Used a socket to remove the electronic circuit board and unplug the electrical connectors. Then I plugged the new board in and reattached it.

Some of the connector prongs got bent in shipping I guess but I was able to straighten them.

It was very easy, it took less than 10 minutes
just a few screws.

Screwed in light bulb and glass protector

I slide the oven out from the counter and unpluged it. I removed all the oven racks. I then removed the machine screws that held the sheet metal that covered the back of the unit. This made it a lot easier to disconnect the long oven sensor wire and put the wire through the insulation. I removed the two screws on the inside of the oven that held the sensor onto the inside rear wall of the oven. The old sensor did not test too bad but the temperature is reaching the set temperature. I still had to adjust the oven temp up ten degrees using the control panel. I have learned that it takes a few cycles of the element going off and on during the warming to reach the desired set temperature. One more issue is that the buzzer goes off signaling that the set temperature has been reached when it has not. When I set it for 350 F the buzzerr goes off at 280 F and I have a good oven thermometer. I own three oven thermometers and they all read the same. We use to have nothing but Maytag appliances but no more. We have had issues with Maytag front loading washers and ranges. PartSelect is great. Good prices and fast delivery.

shut power to unit removed front top cover,four screws holding it down.diconnect element and install new one.its that easy.

I have a stacked microwave and oven. Removing the oven control panel was easy, removing the circuit board was easy, Replacing the wiring strips and board was easy. Reataching the control panel with the four screws was the hardest part., Gotta wirk upside down!! Saved about $200 doing it myself.