JJW8527CAS Jenn-Air Wall Oven - Instructions

Removed frame to cabinet lag screws
Slid oven out of cabinet (required because wire harness could not be pulled through inside of oven)
Removed two screws holding attaching sensor inside oven
Uncoupled wire harness
Installed new sensor in reverse order

Unfortunately, neither the new bake element or sensor fixed the problem, so I just ordered the more expensive control board -- hope that does it.

As per instructions on the web, removed 3 screws to get round metal plate out to get to wires, removed 2 screws to get element out, it was a breeze.

7 minutes to turn off the breaker - unscrew the old element, pull out the old element attach the new element and rescrew. 10 minutes to replace the broken bulb since the base was left without the glass bulb to turn.

Control panel was responsive however oven would not heat up. I Replaced sensor with one of the adapters and oven is now working again.

Turned off power to the oven
I removed the three screws holding the front panel on, then tilted it slightly and removed it. Then gently pulled the three wiring clips off the posts and set the panel down. Removed the 4 screws holing the dispay with a 1/4 " nutdriver and replaced the screen and reversed the procedure. Turned the power on and it worked!!

1. Remove 4 screws at the bottom of the control panel (above oven door) that hold it in place.
2. Pull the control panel away from oven and lift to remove.
3. Unplug two wire connectors to remove panel from oven.
4. Unplug two wire connectors from the clock panel. Used a putty knife to disengage the connector locking mechanism.
5. Remove 4 screws holding clock in place.
6-10. Installed new clock in reverse order of removal.

It was very easy, it took less than 10 minutes
just a few screws.

I slide the oven out from the counter and unpluged it. I removed all the oven racks. I then removed the machine screws that held the sheet metal that covered the back of the unit. This made it a lot easier to disconnect the long oven sensor wire and put the wire through the insulation. I removed the two screws on the inside of the oven that held the sensor onto the inside rear wall of the oven. The old sensor did not test too bad but the temperature is reaching the set temperature. I still had to adjust the oven temp up ten degrees using the control panel. I have learned that it takes a few cycles of the element going off and on during the warming to reach the desired set temperature. One more issue is that the buzzer goes off signaling that the set temperature has been reached when it has not. When I set it for 350 F the buzzerr goes off at 280 F and I have a good oven thermometer. I own three oven thermometers and they all read the same. We use to have nothing but Maytag appliances but no more. We have had issues with Maytag front loading washers and ranges. PartSelect is great. Good prices and fast delivery.

shut power to unit removed front top cover,four screws holding it down.diconnect element and install new one.its that easy.

I have a stacked microwave and oven. Removing the oven control panel was easy, removing the circuit board was easy, Replacing the wiring strips and board was easy. Reataching the control panel with the four screws was the hardest part., Gotta wirk upside down!! Saved about $200 doing it myself.

very easy

We followed the 63 year old lady's repair directions found on this website and were able to install the new display board in less than 15 minutes. As she said, it was really easy!

I unscrewed the cover on the oven. Used a socket to remove the electronic circuit board and unplug the electrical connectors. Then I plugged the new board in and reattached it.

Some of the connector prongs got bent in shipping I guess but I was able to straighten them.

Screwed in light bulb and glass protector

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.