This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
$15.95
In Stock
Order within the next 11 hrs and your part ships today!
Are you having issues with the performance of your Whirlpool wall oven? The blower motor could be the solution. This crucial, genuine Whirlpool part optimizes the functionality of your oven, helping i...
$302.66
In Stock
Order within the next 11 hrs and your part ships today!
This electronic control board acts as the brain of your appliance, managing temperature, cycle timing, and operational settings. A failing board can cause error codes, irregular performance, or comple...
$261.06
In Stock
Order within the next 11 hrs and your part ships today!
Questions And Answers for JJW2427WS00
Ask our experts a question about this model and we'll get back to you as soon as possible!
1 question answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Anita
November 27, 2024
Do you have a part to repair my Jennair oven?The code is F6E1. The blower fan is not working.
For model number JJW2427WS00
Hi Anita,
Thank you for your question. The F6 E1 error code indicates that there is communications error between the main control board and the touchpad. Try turning circuit breaker off for 60 seconds to reset the oven. If the code reappears, you will need to replace the electronic control board. We hope this helps!
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Remove the oven door. Remove 3 self tappers on rear wall of oven to take off a round access panel. Pull out a pre-cut rectangle of insulation. Next I removed the 2 screws holding the sensor in place. Pulling the sensor out a bit told me I was "touching" the correct wires in the SMALL rectangular opening. The wires are not visable and 2 hands do not fit in this small opening.I looked at the NEW sensor to see the release on the sensor plug. Slip the angled needle nose into the opening and grasp the plug/release side. The plug pulled apart easily. The sensor wire pulls out with a little bit of twisting to fit it out the hole. The new plug pushes in and has to be worked down to where you can reach it. The same angled plier works to re-attach it. It takes longer to read this than to do the job. Best of luck, Al
If doing this for the first time, it's harder to replace than described by others.
Start by removing the oven door. Reach in to unscrew the two screws that hold the sensor in place on the back wall of the oven. I was working on the upper oven of a double wall oven and found it more comfortable to sit on a tall bar stool while working. Pull the sensor partially out and you will see the connector wire running through the sensor opening. The sensor connector plug is too deep into the oven to reach with fingers or any tool. Next unscrew the 6" round heat circulator fan just below the sensor on the back wall of the oven. Pull the fan partially out and you will see the plug for the temp sensor directly behind. You may have to push some of the insulation of out of way. Unplug the old sensor and pull it back out directly through the sensor opening. Take the new sensor and thread it in through the opening and plug it in. Reinstall the circulator fan and then screw the new sensor in place. This should complete the temp sensor replacement.
