All Installation Instructions for General Electric Range JGSP28SEK3SS

Malfunctioning Regulator

I replaced the regulator because it would close off when not in use. The regulator would not allow gas to flow for 15-45 seconds after 1 or more valves were opened. Everything functioned fine after the gas started flowing, but after a few minutes of having all burners off, you would have to wait for the regulator to open up when you needed to cook again. It was not the biggest problem in the world, but my wife complained like it was. The fix was easy and not to expensive, especially when you consider how much she was willing to pay the repair man. Hands on work was about 10 minutes. Gathering tools and teaching my son what I was doing took up the bulk of the time.

Parts Used:

Pressure Regulator

Jesse from Lubbock, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Wrench set

1 of 4 people found this instruction helpful.

Was this instruction helpful to you?

To Replace Gas And Burner Parts In Section 4

Start by removing all screws 3 for each burner total of 15 t-15 bit is required then proceed to remove spark igniters 5 total slight pull next step would be to slide a screwdriver under top left and right side to remove top shelf. There you will have access to the parts you need to replace. When done just reverse installation instructions to complete

Parts Used:

Top Burner Spark Electrode

John from Long Beach, NY
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Wrench set

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

oven was not getting up to temp

Once I opened up the back of the range, the sensor wires where there and burnt just like your info said. One nut to take off in the oven and the sensor came right out and the new one went right in. The oven works great, cooked the turkey today. The worst part of the repare was the cleaning behind and under the range, it hasn't moved since it was put in 6 years ago. Very pleased with PS.

Parts Used:

Temperature Sensor

walter from townshend, VT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Leaking from front door

First remove the screws around the inside perimeter of the door. These require a special hex driver. Take off the inside plastic liner of door.
Peal off the old Insulation Foam Strip and replace it with the new strip in the same location. Make sure the wires are off to the right side. Replace the door plastic liner. Done. The Insulation Foam Strip really acts more like a loose gasket to keep spashing from creeping under the door and drippin out on the floor.

Parts Used:

Grate Foot

Gene from Simi Valley, CA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

1 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Burner would not ignite.

Could not have been simpler. Burner head dropped into place and was held in place by gravity. Not possible for part to go in incorrectly.

Parts Used:

Burner Head - Medium - 9500

John from Los Angeles, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Missing grate foot.

Ordered by phone parts & very pleased with all of transaction.

Parts Used:

Grate Foot

Barbara J from Sweetwater, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

Was this instruction helpful to you?

the grate foots came off

put it in but it keeps falling out. they're made narrower than my oven grate.

Parts Used:

Grate Foot

Sandra from Watertown, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Flashing F2 and erratic temperature readings.

Unplugged from wall outlet, then opened oven front door. Reached in and removed two screws. Pulled oven sensor threw and detached electrical connector from old sensor. Plugged in new oven sensor and reversed removal procedure. No more Flashing F2 and oven temperature came to ready. Very easy.

Parts Used:

Temperature Sensor

Kenneth from Salem, OR
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Hard to move drawer in and out because the rear drawer supports broke off.

Repair was very easy - less than a few minutes - just had to screw in 2 screws to the new drawer supports.

Parts Used:

REAR SUPPORT

Steven from Lansdale, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Missing oven rack

I opened oven and pushed oven rack inside.

Parts Used:

Oven Rack

Damaris from Easton, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

no racks to oven

Easily glide in.

Parts Used:

Oven Rack

Johnette from Baltimore, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

F2 error code

Really easy fix. Unplug oven. With a 5/16 nut driver take the 5 screws out of the center long tin cover and remove. Unplug little white temperature sensor plug located between broil heating element. Open oven door and remove one screw holding temp. sensor using same nut driver and simply pull out old sensor. Install new sensor. It's that easy. No more f2 been working like a champ!!!

Parts Used:

Temperature Sensor

jud from gatesville, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Broiler and Burners would light, oven would not light and you could smell gas, also before the oven stopped working the oven was taking awhile before it would light

1.Removed the oven door. 2. Removed the oven floor panel ( slides right out ). 3. Removed cover plate and and removed one screw holding the igniter in place. 4 was able to pull the wire into the oven and unplug the igniter. Ordered a oven temp sensor but never needed it.

Parts Used: