This part is a replacement halogen lamp for your oven. The bulb is 25 watts and 120 volts. If your light bulb is burned out, this is the part that replaces it. Be sure to turn off power to your range ...
$32.66
In Stock
Order within the next 12 hrs and your part ships today!
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
$28.95
In Stock
Order within the next 12 hrs and your part ships today!
Keep your oven safe and functional with this replacement interior door glass, the heat-resistant panel that lines the inside of your oven door. With dimensions of approximately 20 5/8" x 13 1/8", it f...
$160.20
In Stock
Order within the next 12 hrs and your part ships today!
Order within the next 12 hrs and your part ships today!
Questions And Answers for JGS8850ADB
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Dan
December 24, 2019
We replaced part PS2003225 with your suggestion about a F3-1 error message. The oven was turned on and we got same message. The oven also takes a prolonged period to heat to desired cook temperature.
For model number JGS8850ADB
Hi Dan,
Thank you for your question. If you have replaced the sensor and the error code is still coming up, you will need to check the connection between the oven control and oven sensor, as well as the sensor harness to see which part is causing the issue. We hope this helps. Thank you and have a great day!
Was this helpful?
Thank you for voting!
Andrea
March 24, 2022
Good day....issue with all 4 igniters sparking continuously when burners on or off. the burners do come on when turned on. all is clean......any input is greatly appreciated....andrea
For model number JGS8850ADB
Hello Andrea, Thank you for your inquiry. We have researched the model number you have provided and would recommend checking the spark module, the spark igniters, and the spark igniter switches. You can test the parts with a multimeter. If you are unfamiliar with how a multimeter functions, we have videos available to assist you. We hope this helps and if you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
I get an f8 error on my stove and it ceases to function and beeps. I have to
unplug the unit for a day, then it works for a while. After a couple of days the
same thing happens again. What causes this and what part do I need to
replace to fix the problem?
For model number JGS8850ADB
Hi Vernell, thank you for getting in touch. The F8 error code indicates a shorted meat probe. To troubleshoot it, start by checking the wiring connection between the oven control and the meat probe. If wiring is ok, you may need to replace the oven meat probe sensor/temperature probe, part number PS11743863. We hope this solves your problem!
My oven has two igniters so I needed to determine which one was the problem.
Using the amp/multi meter I tested the connection between the igniters and the valve, with the oven turned on, to find the bad igniter. Depending on the model of stove you have, the amp reading you need for a properly functioning igniter will vary. My lower igniter read 2.7 amps with a rated amp between 3.3 and 3.6. So that was the culprit.
Replacing the igniter was easy. Two screws and a wire connected with a plug. I was able to do the diagnosis and unplug the wire without pulling the oven out. I pulled the drawer out and removed the two screws in a cover behind where the drawer was. You may not be so lucky…I have long arms.
I found removing the oven door made it easier to reach the igniter itself. To remove the door just open it slightly and pull up, it should come off easy…and replace in opposite manner.
Keep track of your screws and put it back together the way you found it except for the igniter that is.
Anyone with moderate technical skill could easily do this repair. The diagnosis is the hard part. I estimate I saved about $200 doing it myself.
Repair tech checked oven and said the control panel was bad and needed to be replaced. The new control panel would cost over $450.00! I found that the oven sensor was bad and replaced it for $30.00. The old oven sensor had failed following a self cleaning cycle. I found that the wires coming out of it were burnt.
Replacing the oven sensor was very easy. I removed the back panels 6 screws to gain access to the sensor's connection. I then removed the 2 screw that hold the sensor in place inside the oven and pulled the old sensor out through the oven. I reversed this process to place the new sensor in the oven.
I removed the oven door, unscrewed a couple of screws, replaced the ignitor, put screws back in, done! Sometimes it would take my oven up to an hour to heat up and sometimes it just wouldn't heat up, just fill the house with a gas smell. Now, it heats up in about 3 minutes!! We were considering buying a new oven, we will just keep this one. $40.00 beats $700.00
