This grease filter is almost fourteen inches long and almost twelve inches wide. This filter is intended for use with some downdraft cooktops and ranges.
$49.14
In Stock
Order within the next 6 hrs and your part ships today!
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
$28.95
In Stock
Order within the next 6 hrs and your part ships today!
This surface burner head is for ranges.
Surface burner head distributes the gas through holes or slots to create an even flame across the cooking area.
Shut off the gas supply and unplug the ran...
$177.02
In Stock
Order within the next 6 hrs and your part ships today!
This is the replacement brass seal for your range or cooktop. It is made of brass and is approximately 1 inch in diameter. This part may also be known as the surface burner orifice holder seal. It pre...
$10.18
In Stock
Order within the next 6 hrs and your part ships today!
This exhaust vent blower wheel is almost seven inches in diameter, and just under four inches deep. It is made entirely of metal and is used with a range's venting system.
$150.75
In Stock
Order within the next 6 hrs and your part ships today!
This range fan switch is designed to control the operation of the cooktop or range ventilation system, allowing the downdraft or blower fan to start, stop, or regulate airflow as needed to manage heat...
$337.57
In Stock
Order within the next 6 hrs and your part ships today!
Questions And Answers for JGD8345ADB
Ask our experts a question about this model and we'll get back to you as soon as possible!
5 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jennifer
November 9, 2022
Can this unit be changed from gas to propane with a conversion kit?
For model number JGD8345ADB
Hello Jennifer, thank you for contacting us. Yes, the appliance, model number JGD8345ADB, is convertible to propane. You will need the LP conversion kit, part number PS2083757. Customer service is always available to help you place an order if you are having trouble doing so. Good luck with your repair.
Hi Juanita, thank you for your query. According to our research, your unit was most likely manufactured in 2000. For a more accurate result, we will need the serial number. We hope this information helps!
Was this helpful?
Thank you for voting!
Kathy
October 23, 2023
Can I replace the grill with 2 burners?
I have a gas unit, serial #17573888LN,
THANK YOU
For model number JGD8345ADB
Hi Kathy, thank you for reaching out. Based on our research, your model comes with a double burner grate, part number PS11744605, that covers two burners. We hope this information is useful!
Hi Joseph,
Thank you for your question. If the burner valve has seized, you can remove it from the stove and take it apart to clean it, to see if that helps, but we would recommend replacing it. The part number for the burner valve is PS11744555. We hope this helps!
One of the coktop burners will not lite. The igniter does not spark. All of the other burners work properly. The igniter has been replaced but still does not spark.
For model number JGD8345ADB
Hello Jason, thank you for contacting us. Make sure the burner cap and base are properly aligned and seated. If they're not, the igniter won't spark. Ensure the burner ports and ignition ports are not clogged with food debris or spills. Use a small brush or a toothpick to clean out any blockages. If this does not help, you will need to replace the spark module, part number PS2094592, to fix the issue. If the burner is clean but still won't spark, the spark module itself may be faulty and need replacement. We hope this information helps!
Lift out sealed burner assembly rear of stove first while careully sliding to rear to disengage ignitor probes.Remove philips head screws from bottom sheet metal housing to expose bottom of burners Remove gas tube assembly screws and move tube away carefully.Unplug wires from ignitor.Remove screws for ignitor .Remove ignitor, I noticed that rust and dirt had built up around burner to pan connection.I used my oil filter wrench to turn slightly the burner to remove it from the pan to clean.Reassembled in reverse order.
