JF42NXFXDW01 Jenn-Air Refrigerator - Instructions

took off old filter put in new - simple

Popped the old one out with a kitchen knife and popped the new one back in. It tool less than 15 seconds!!

My owners manual said to unplug fridge from elec outlet, use a kitchen knife to gently pry off the switch plate
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!

Sincerely, Ron Marshall, Billings, MT

I pried the old one out with a screw driver and pushed the new one in. I expected instructions in the box it came in but there were none.

Loosen to screws under ice mold and unplug power cord from icemaker.Lift out complete unit. Remove cover on ice maker,then 3 screws on end plate and remove end plate. Remove 2 screws that hold ice mold to frame. Make sure that the thermostat is moved to new mold. Reverse order to install new mold.

Used the instructions on your site.

Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.

I watched the video and thought "I can do this". Made some notes and then proceeded to remove the old switch and replace with the new one. Thank you.

I have never before seen a bulb with the filament intact not light. If the bulb's filament seems intact, screw the bulb into a known working lamp and see if it lights. When screwing it back into the socket in the fridge, it takes a bit of extra effort to fully seat (until it does, it won't light!). For replacing the switch, I unplugged the unit, used a paint scraper and worked it under the switch bezel from the right side. A bit of moxie, and the switch came out. The replacement switch had a different spade contact spacing than the original. I used a pair of scissors to cut the rubber bridge between the two switch wire connectors so I could connect to the new switch. In the end, it turned out to be the bulb. NOTE: The Model TC18KL is _not_ listed! What I finally found that the number "P7803211WL" on the sticker is actually a manufacturing code. Found this out by searching, and Sears' part search came up with matches.

The refrigerator stopped working and temperatures were rising. After inspection, noticed that the compressor is not running and condenser fan not running. I ordered the inverter box and replaced the old one. Compressor started to run but condenser fan still not running. Compressor was getting hot while freezer temperature reduced to some degree. Cleaned condenser with compressed air, connected condenser fan directly to 110VAC. Refrigerator runs normally. Burning of the inverter box may be preventable. We did notice that the freezer portion of the door frame getting hot for over 3 months. This is an indication that the condenser does not provide sufficient heat dissipation. This in turn made the compressor hot and melted away some components in the inverter box which is located next to the compressor. A thorough cleaning of the condenser made the freezer door frame stay slightly warm but not hot. This condition keeps the compressor running at normal temperature. I still need the main controller which is discontinued to automatically control the condenser fan. So far the fan runs all the time and uses a bit more electricity than necessary.

Just had to take the old one out and put the new one in. No problem.

new filter cap fit perfectly, but I couldn't get filter in or out. Called appliance repair person who pushed it in -- no problem. I just didn't have enough arm force to push it in.

Took off Old Cap Put Knew One On.

push button take old one off put cap on new one,push it back in.easiest thing ever.

popped out the old one and popped in the new one