JEW9627AAS Jenn-Air Wall Oven - Instructions

I slide the oven out from the counter and unpluged it. I removed all the oven racks. I then removed the machine screws that held the sheet metal that covered the back of the unit. This made it a lot easier to disconnect the long oven sensor wire and put the wire through the insulation. I removed the two screws on the inside of the oven that held the sensor onto the inside rear wall of the oven. The old sensor did not test too bad but the temperature is reaching the set temperature. I still had to adjust the oven temp up ten degrees using the control panel. I have learned that it takes a few cycles of the element going off and on during the warming to reach the desired set temperature. One more issue is that the buzzer goes off signaling that the set temperature has been reached when it has not. When I set it for 350 F the buzzerr goes off at 280 F and I have a good oven thermometer. I own three oven thermometers and they all read the same. We use to have nothing but Maytag appliances but no more. We have had issues with Maytag front loading washers and ranges. PartSelect is great. Good prices and fast delivery.

(turn off the breaker to the oven.)take the eight screws that hold the oven in the wall out. then cut a piece of wood about 3/4" square 29 3/4" long to hold the oven out away from the wall while changing the control panel. there is four screws below the control panel to remove. lift the panel towards you and raise it up . disconnect the wires carefully. set the panel on a counter and remove the four screws that hold it in place. change the control board and reverse the process. turn the breaker back on and you are done. very simple job,

very easy

removed panel, removed clock and installed new clock, reinstalled panel

Removed a couple of screws and removed display panel. Replaced clock display on back of the panel- was held on by two small hex head screws -1/4" nut driver and phillips screw driver were the only tools required, very easy repair that
the appliance repair man wanted 750$ to do.

Screwed in light bulb and glass protector

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

removed the four philips screw on the oen cover plate. slid the plate off and disconnected the serial wires. removed the four 1/4 hex nuts holding the control panel on. replaced with the new control panel and replaced the four screw nuts. re-assembled the serial wires, placed the coveer plate and replaced the four set screws. that easy.

Removed 4 screws thathold the diplay panel on, unplugged three electrical connectors and removed for screws holding the display on. Easy!

Husband got on partselect.com and read reviews, we ordered a long oven sensor kit. When it came in the mail, I took it out and look at it, decided I could probably switch the part.... and so I did. Easy Breezy ... and it worked well

Our oven quit working again. I called the repair(dealer) man and he said we needed a new control panel. It would cost $180.00 and labor would be $60. The total repair would be $240.00. We considered just purchasing a new one. It is a slide-in range and they start at about $1500. So I began looking for a control panel on line. I found your web site and entered what was wrong with the oven. Your site suggested we try replacing the oven sensor. There was a video that showed how simple the repair was. We ordered the part. It came quickly and I immediately made the repair (about 10 min). I was very disappointed that it did not work. I went back to you web site and tried the next option. It was a terminal block for only $20.00. I didn't even know what a terminal block was, what it looked like or where on the range to find it. But I went again to your video and I learned quickly what to do. I ordered the part and it came in two days. I made the repair in about 15 min. My wife was very happy that the repair worked. Our total cost was about $80. The $240 quote would not have fixed the oven anyway. The repairman was wrong. I was very happy with the results and the money we saved.. Good Job PartSelect and thanks.

Removed two screws, unplugged the old unit, plugged in the new, screwed the new in. Job done. Would have been less than five minutes if I hadn't kept dropping the screws.

Took out two screws, disconnected the old element and replaced with the new one. Very easy - oven was up and running in no time at all.

Parts no longer available so we went to several appliance stores and measured racks. We found a jenair model had racks that measured correctly got the model number and ordered the racks. There working great and now the oven looks like new. Our kitchen is a restored 1956 GE metal kitchen in Cadilac pink. Thanks guys for the fast service and very resonsble price. Was also very happy to find the racks were made in USA.

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.