JE856E1 General Electric Range - Overview
Sections of the JE856E1
[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Trim Ring - 6 Inch
PartSelect #: PS244475
Manufacturer #: WB31X5013
This 6 inch high rise burner trim ring is intended for use with detached style low rise tilt lock surface mount burners on ranges.
$13.95
Special Order
Trim Ring - 8 Inch
PartSelect #: PS244479
Manufacturer #: WB31X5014
This 8 inch high rise burner trim ring is intended for use with detached style low rise tilt lock surface mount burners on ranges.
$15.95
Special Order
Broil Element
PartSelect #: PS249411
Manufacturer #: WB44X173
The depth of the screw-on terminals is 2-3/4 inches and they are 1-1/4 inches apart. Does NOT include mounting bracket.
$70.57
Special Order
Drip Bowl - 6 Inch
PartSelect #: PS244677
Manufacturer #: WB32X10012
This six inch chrome drip bowl is intended for use with tilt lock style surface mount burner element units.
$19.95
Special Order
Range Infinite Heat Switch Kit
PartSelect #: PS16216966
Manufacturer #: WB21X36771
The infinite switch controls the stove top surface burner. This switch will work with most of the electrical range models with coil burner elements.
No Longer Available
Drip Bowl - 8 Inch
PartSelect #: PS244680
Manufacturer #: WB32X10013
This eight inch chrome drip bowl is intended for use with with tilt lock style surface mount burner element units.
$26.95
Special Order
Tilt Lock Hinge Mounted Surface Burner Kit - 6"
PartSelect #: PS244042
Manufacturer #: WB30X342
This genuine 6-inch surface heating element provides the heat needed for cooking on compatible electric ranges and cooktops. Designed with a tilt-lock hinge mounting system, it delivers consistent hea...
$125.06
Special Order
8 Inch Surface Burner
PartSelect #: PS244046
Manufacturer #: WB30X348
This surface element kit includes an 8 inch element, two wire, 2350 watt surface element, and a terminal block with all three-wire units. These high rise elements do not come with an attached trim ring.
$123.56
Special Order
Oven Sensor
PartSelect #: PS235718
Manufacturer #: WB21X158
This sensor offers 16 ohms of resistance at room temperature, though the resistance increases as the temperature increases.
No Longer Available
Common Symptoms of the JE856E1
[Viewing 5 of 5]Element will not heat
Fixed by
these parts
these parts
Show All
Little to no heat when broiling
Fixed by
these parts
these parts
Show All
Little to no heat when baking
Fixed by
these parts
these parts
Show All
Oven not heating evenly
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Needed to replace Drip Pans and Trim Rings for old stove
Repair was simple (just lift off the old and put on the new). What was pleasantly surprising was how quickly I received the parts (amazing)!
Lastly, I've been looking for the correct parts/sizes in stores for years (yes, I should have tried this sooner). I was delighted to finally find a place that actually had the correct parts.
Lastly, I've been looking for the correct parts/sizes in stores for years (yes, I should have tried this sooner). I was delighted to finally find a place that actually had the correct parts.
Parts Used:
-
Cynthia from Tampa, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
40 of 47 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Large burner would operate on high setting only.
1. Removed the back panel.
2. Disconnected the wires from the old switch while connecting wires to the new switch one at a time.
3. Installed the new switch and broke off the excess metal on the post which fits into the burner knob on front of the range.
4. Replaced the burner knob and replaced the back panel.
2. Disconnected the wires from the old switch while connecting wires to the new switch one at a time.
3. Installed the new switch and broke off the excess metal on the post which fits into the burner knob on front of the range.
4. Replaced the burner knob and replaced the back panel.
Parts Used:
-
Ernest from Bellevue, NE
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Socket set
22 of 28 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven temperature too low
After ordering the proper part with the help of the phone customer service tech, I moved the stove from the wall, unclipped the connector, removed the two screws holding the sensor in place, and removed it. Reversed the above to put it back, and the oven holds perfect temperature.
Parts Used:
-
Ryan from Henderson, NV
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
17 of 19 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!