JE1860SH03 General Electric Microwave - Instructions

I received my replacement and it is perfect! Thank you so much for for your fast shipping and delivery.

After reading reviews that there was no power what so ever and a fuse replacement will solve the problem, I tried it. Replacing the fuse is very easy (and I am not handy at all). All you have to do is remove the microwave cover from the top by removing two screws, slide the cover to the left and pulling the cover off. Then remove the grill in front of you, by removing one or two screws. The fuse is in front of you, use pliers and be firm but gentle. Replacing the fuse is easy but it did not solve my problem.

It was extremely easy. I put the microwave on my table upside down and could see the motor thru the holes in the bottom cover. It appeared as though the outside skin had to be removed to access the motor but after looking at it there is an access panel I did have to cut it loose. Not bolted on. There was a message stamped into the bottom case next to the panel that said to debur after panel is removed. So I cut it loose on 3 sides was able get to the one screw swap the motor and reinstall it in about 5 minutes. It works like new What an easy and quick repair. Thanks

I removed the new tray from the box and slid it into the microwave. That's it.

Removed microwave cover using screwdriver and anti tamper bit available at local hardware store. Megnetron had broken magnet making discovery of deffective part easy. Removed wire connector and three screws attaching magnetron to case, removed magnetron and installed new item in reverse order. Installed cover and made popcorn for operational check of microwave. Happy days..........

I did the repair in less time than getting the part, WHICH WAS FANTASTIC. Took a needle nose to get out the broken part and put the new one in. Works like new ! Recommend this place for repair parts, but this is just my own experience.

First unplugged the microwave, took top grill off, took control panel off, took wires off and used color coded tape to make sure they went back in right places, took fuse out and replaced it and put every thing back and it all worked fine and to top it off my wife did it all. So it was pretty easy.

Very easy you just have to make sure that the tray is in the groves for the wheels :)This is the best place to shop as I have used them on all kinds of appliances and they have never let me down when it comes to price and delivery time!

Easy-easy-easy...just took out the old broken tray and installed the new one. We did the same with the ring. The service from this company was excellent!! Ordered on a Saturday and received it on Tuesday....

remove the glass, remove the rotating ring, install the new ring, replace the glass and my wife fixed it in 30 seconds.thanks for the providing the part.Ed

I went on line, put in microwave repair and watched a video on repair. I then took the oven down from over the range and took it apart. I could see were the magnetron had burned out. There was a hole with obvious burn marks. I went on line looking for the needed part. I clicked on PartSelect and order the magnetron. I received the part within three days, regular shipping. As I had not put the oven back together it took only a few moments to save 150 to 200+ dollars. I put it back together and happy, happy me, it worked.

I only had to snap the parts into place

I pulled out the unit and found 2 interlock switches that are depressed when the door closes. After cycling the door open/closed I found that one of the switches occasionally would stay depressed. The repair was easy (after I took off the panels so I could get to the switch) I simply removed 2 screws that attached the interlock switch assemblies to the main unit. Then I popped out the defective switch and popped in the new one. This did indeed fix my problem.

Used diagram on the web-site and a screw driver to replace the fuse and just one of the 2-Terminal Micro-Switches. When I looked at the three micro-switches one of them had a brown connector and you could see it had been burned. I just replaced that 2-Terminal Microswitch and the connector and the Fuse. Now the Microwave is working fine.