JDPSS244LL0 Maytag Dishwasher - Instructions

I called an experienced plumber, who balanced and installed my new dishwasher properly, using the brackets I ordered from Parts Select, after an INEXPERIENCED plumber had tossed the factory-provided mounting brackets out with the shipping carton. Relief!

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

After pulling the dishwasher out, I was able to determine the leak was occurring around the plastic nuts on the end of the heating element. I removed the heating element and saw that even though there were washers on the ends that protruded through the backside of the machine, they really weren't sealing the holes the element was sticking through. Looking at YouTube videos on the installation procedure, I noticed the element being installed had a sort of metal grommet permanently affixed to each end and the rubber washers were between the grommet and the dishwasher body. I ordered the new part and saw this to be when I received the new part. This grommet allowed the washer to seal the hole, once the plastic nuts were installed on the backside of the dishwasher. This seems to have stopped the leak. I don't know how the original part ever worked correctly, since the washers freely sat on the element with nothing to force them up against the body of the dishwasher and seal the holes. It may have been leaking long before I discovered the problem.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

The valve has a plastic fitting to attach the the water line with a hose fitting. Was not carful enough with the original and damaged it attaching the water line. Ordered a replacement fitting. While it is possible to replace the water inlet valve without pulling the dishwasher out from the cabinet found it was easier to get at with the machine out. The video does and good job of showing the removal and replacing the valve. Easy job, don't be like me and be careful attaching the water line.

Removed old part and replaced with new part

I simply had to hook up the power cord to the dishwasher so i could plug it into the outlet rather than direct wire the appliance. Everything went very smoothly. Everything needed for installation other than tools was provided. Easy to follow instructions if you know a little about electrical wiring.

Turn off water and disconnect water line.
Pull dishwasher out as far as possible.
loosen both door hinges, with a helper holding the door at an angle.
Disconnect connecting wire between hinges.
Remove and replace left door hinge. Then remove and replace the right hinge.
Reconnect every thing, turn on water.
Hinge is a poor design. Ours had grease on the spring and it had slipped off the connection.

Recently bought a whirlpool dishwasher, the dishwasher was converted to a portable dishwasher and they did not use the cord application power cord so they machine was blowing our breaker, instructions were very simple and installation was easy!

removed and installed cords with screw driver

I found it best to lay the dishwasher on it's side, this makes it easier to attach a 90 degree hose fitting without cross threading the plastic fitting.

Remove power source, then remove old power cord.Run new power cord through existing opening ang attach to existing power box on bottom o f dishwasher. Install electrical leads and device ground. Reinstall cabinet bottom. Check out operation by running a cycle. All ok!

followed directions, a kid could have done it,

I just popped the new one onto the bottom of the middle rack and it was done. Easiest repair I have EVER done!

Inner gasket (Part # PS16221119) was angled in at the corners, so it wouldn't make a seal with the door, resulting in steam leakage and damage to adjacent cabinet door. Simply pulled out old gasket, pushed new one into track and voila, problem solved. New gasket angles out at corners, creating steam-tight seal.