JDB3000AWS2 Jenn-Air Dishwasher - Instructions

Didn't have to remove any screws, etc. Just had to pull the old gasket out of a grove in the top and sides of the frame, clean up the particles caused by the deterioration of the old gasket, and install the new gasket. Have to be careful to start at the top center of the frame exactly in the midpoint of the gasket and carefully push the gasket into the grove with your hands. Try not to stretch the gasket. There will be about 2 inches of extra gasket laying on the bottom on each side of the dishwasher, and that is OK.

First let me tell you I am not a "handyman". I am a 50 year old housewife who was determined not to shell out $$$ if I could help it. I researched on the internet what could be the problem...it was more than likely the chopper assembly. I found a youtube video that showed how to get to the chopper assembly. So I removed the racks by dislodging the end clips. Next I took the bottom tub sprayer off by holding the middle with my fingers and turning the blade counter clockwise. Next, I unscrewed the line that ran in the back and up to the top sprayer (I only removed the one screw so I could slide it to the right slightly so I could remove it from the connector at the bottom and it revealed four screws that needed to come out of the mesh cover. After removing that there is one more screw that comes out of the shroud that covers the chopper assembly. I cleaned the area removed the chopper assembly (totally gunked up) and replaced it with the new one I purchased here...(lightening fast shipping btw!!...Yea! for PartsSelect.com....you guys rock!) I checked for gunk in the rubber valve assembly, super easy to remove/replace. Vacuumed standing water with my shop vac to get any errant noodles and food bits and reassembled all of the housing and lines in reverse order. Before I ran my dishwasher I put some clean water in the bottom...just poured about 32 oz in. Whether you need to or not....I don't know but figured it wouldn't hurt. IT WORKED LIKE A CHAMP! Super clean dishes again!! I felt so empowered and the whole thing cost me less than 20 bucks! Listen ladies....and men....this is super easy....If I can do it....any one can!

1. Put a towel over the bottom of the machine. (In case you drop the screw... duh!)

2. Remove the top screw.

3. Replace the snap pin (pointy end DOWN.)

4. Snap the spinner in place.

5. Replace the screw. (Or go to the hardware store to replace the screw you dropped into the bottom of the dishwasher. Dashitall!)

Took racks out, loosen screw on top and back then twist feed tube to right and whole assembly can be removed. Now you should be able to see some torx screws; remove those and then remove the piece they were holding down, from there you'll see another screw, remove it and the piece and so on until there are no more screws. Now there is the food chopper cover that needs to be removed; mine was stuck there. You should notice some ribs underneath that allow the water to be sucked in while keeping really big pieces out; I got a pair of channel-locks, opened them all the way and was able to slip one of the pieces under the cover and pull straight up, once off you will see the chopper covvered in food. I cleaned mine off and it looked good, but when I put it back and stuck my finger down teh discharge tube and turned the pump, the chpper did not turn. when I put the new one in and did the same test it did turn. If the chopper is still fits in the slot, it can be cleaned and put back and work for several washes while the part is shipped. I went ahead and changed the check valve since I had it opened which is just to the right of the chopper(all you can see is a little slit and some black rubber). Use some needle nose and pull it out. I would not do this unless you plan on changing it, I pulled mine out to look at it and when I put it back so I could order the parts the dishwasher never drained properly. When you compare a new one with an old one you will see what I mean, you can drop a new one right in but the old one you will have to force in (gets water logged over time and expands). This job is very easy and a lot cheaper than a new DW...and your wife will be impressed, so do not be intimidated.

After unscrewing the dishwasher, I pulled out the washer, I saw that the springs were attached just by strings that were broken... I just used the strings from an old lanyard, retied everything, and did not need the springs! works well!

Very easy to install the new B Metal Fuse. Removed torx head screws holding the outer door panel on the dish washer. Removed the fuse and two wires connected to the fuse. Inserted the new fuse in the holder and plugged the two wire connectors back
on. Installed the outer door panel back on, turned the breaker back and the machine powered back up. Very easy install and saved a service call. Total repair cost $24

Checked grinder and cleaned it several times, adjusted blades. Dishes would be clean for approx. 6 cycles, then would not clean. Placed dishwasher on its front and removed the motor. Removed grinder and impeller which I found to be worn so that the blades would not turn on the grinder which caused it to collect food particles. The impeller locks in easily.

I shut off the power to the dishwasher, then I removed the front panel under the door. On the right side just behind the electrical box there are two wires going up to the hi-limit thermostat, (you may need a small mirror to see it), remove one screw that is holding the thermostat bracket, unplug the wires from the old thermostat and install new one. Screw bracket and thermostat back to the underside of the dishwasher, reinstall the front panel, turn on the power, done.

open dishwasher door, use torx socket and ratchet to remove 6 screws. Pull down wash options face, find the bi-metal fuse. Used the directions in the package to replace. popped old fuse out of electrical board, Cut 2 wires, stripped said wires, attached stripped wires in housing on new part, tightened the 2 screws where new wires attach, popped new fuse in electrical board. Reattached face. Very simple and easy to do. Did not fix the problem. Had to get the electrical board that the bi-metal fuse is snapped into. Very easy for someone that has worked on vehicles or electrical things before. If no experience, then I would say it is still easy as long as you follow the directions taht comes with the part. It has pictures as well.

Several hours to diagnose problem: Removed all the plastic water distribution tubes to top rack and found no blockages. removed lower water jets, drain screens using star driver on 6 screws. still could find now blockages. decided problem had to be in pump mounted below unit so completely disconnected unit and removed from under counter. Upon removing lower plate below door I discovered a plastic pouch containing an excellent trouble shooting guide with complete dis-assembly instructions and parts breakout diagrams with P/N listings! First thing I discovered from this was that the chopper assembly was hiding under a plastic cover just under the filter screen I had already removed. The trick was to press down on the right side of the plate to get it to pop up and reveal the chopper. The whole chopper assembly slides out without tools. I found the strainer plate behind the chopper blade totally plugged as the blade had broken off the plastic drive shaft because the retaining knob on the end of the shaft had broken off. I was able to drill and tap the shaft and install a SS machine screw with washer to reassemble the chopper blade on the shaft. Not expecting this "Joe Maggee" repair to last more than a few cycles I went online with the P/N and googled PartSelect. Placed the order and chose std delivery over 2day or next day since I expected the repair to last for the week. I put everything back together and the first load came out perfect! This was Sunday afternoon. Tuesday the part arrived at my doorstep! 15 minutes and the new part was in. My "Joe Maggee" repair is now in the junk drawer awaiting the next pistachio shell that gets run through the washer.

removed both upper and lower racks. removed lower spray arm(left hand thread) removed "water delivry tube and upper spray arm. removed torx screws on pump cover. removed inner chopper cover. Chopper assy had come apart and was full of food crud. cleaned out and installed new chopper assy. kind of tricky don't force it. reassembled. tested OK.could tell sound of more forceful water pressure

First I unplugged the dishwasher.Then I removed 6 Torx screws, popped off cover, cut wires to old fuse, stripped wire, placed wires in new part, tightened screws, reassembled in reverse order, plugged unit back in and tested. WOO HOO!

I saved over $150.00 by doing it myself instead of having a repairman come out! That's 4 free fishing trips!

Started as dishes not getting clean and I observed that the top arm was not spinning and there was very low water pressure coming out of the jets. After making sure the water level was up to the bottom of the heating element and making sure the jets were not clogged I checked the filter and chopper. It was a little tough to get the cover off of the chopper but once I did I could see that the chopper scraper was broken off and the shaft was broken. The screen was all clogged up with stuff. Ordered a new assembly and put it in making sure to compress the spring and make sure the gears lined up. Now it is running great.
I think the Kitchenaid is the same as the Whirlpools.

I watched the instructional videos that showed how to replace the inlet fill hose/water inlet a couple of times. The repair was exactly as shown. No trouble at all.

We were happy to find the basket we needed listed on your website, even after we could not find it on the Maytag site. It was perfect. I can't believe we lasted almost 2 years with the broken basket we had.