JDB1080AWQ41 Jenn-Air Dishwasher - Instructions

I had to lightly pry off the long piece of plastic next to the wheel assembly because I had to twist the assembly counter clockwise to remove the old one. Also had to place the new one so that it rotated clockwise to seat it. Then replaced the other plastic piece.

Lifted out old silverware basket. Set new basket in. Took approximately 20 seconds.

Snapped new wheel on

Remove the screws , opened door panel. Removed switch with latch and replaced with new parts. Replaced panel and screws. Install completed.

seeing as how my husband was out of town, I inserted a regular flatware knife in each of the four slots that held the handle in place on the basket. I then slowly pushed down on the handles of the knives on opposite sides of each other to unlock the handle from two slots on the basket and then went on to push down on the other two flatware knives on the opposite sides...sure enough, the handle came right off...less than 5 minutes in all to take the old handle off from the old basket and then snap it into place onto my newly acquired basket.

I removed the screws around the top and halfway down the sides of the inside of the door. I found that you dont have to remove all 10 screws to access the assembly. Reach in and pulled out the assembly, there was enough slack to pull it out above the door. Pull the connectors off and slide the new ones on. Set the new assembly back in place, insert the 2 top screws first, and then the rest. That was it...very simple to change.

Replacement basket did not include handle so needed to pry old handle off broken unit to use on the new one. Used screw driver to pop loose clips which attached to basket. Had to stick tooth picks broken in half under them to hold out until all four clips were opened at once - then handle could be pulled off. Easily snapped it back on to the new basket and repair was done. Can't get any easier than this!

Easy! Unscrewed panel, took off old latch, put on new. Took about five minutes.

The repair went easy. Just unscrewed the inside door panel and latch assembly. Then put the new one in. The only bad thing was I purchased the latch assembly with out the handle and found out mine was cracked. I looked back on-line and couldn't find just the handle. Everybody sold it with the latch assembly. I thought I would save the 2 bucks buying the assembly without the handle. But in the end the door seals tight and no water leaks.

I pulled out the dishwasher enough to tip it back and put a block of wood underneath the front leveling foot.
This step gave me more room to work on the valve.
I removed the lower cover plates to expose the valve.
I disconnected the incoming water line and unplugged the electrical connection.
I then unscrewed the bracket to release the valve from the case and took off the rubber hose attached to it.
I installed the rubber hose on the new unit and installed the bracket back in place. I then wrapped some Teflon tape on the threads of the valve fitting and re-installed the water supply line. I re-installed the electrical connection.
I then turned on the water to check for leaks. Once I was certain there were no leaks, I re-installed the lower cover plates and took out the wood block and pushed the dishwasher back into place and re-installed the screws that held it in place.
I then ran a load of dishes to make sure everything was working properly.

After disassembling accumulator assembly looking for reasons that washer not washing properly, I noticed accumulator filter had failed. The plastic (or whatever material it is) covering the holes was torn in a couple of different holes. Realizing that this was not the reason for the loss of pressure I investigated a little more and found that water arm going into the docking station was extremely worn with much play. Water pressure was compromised because of it. I replaced filter and docking station and now its like a new dishwasher again. Saved a dishwasher from the landfill!

Dishwasher is in our summer cabin in Colorado so everything has to be drained for the winter. Not really sure whether this leak was freeze caused or that the valve was just old. Couldn't find a crack when I got the old one apart; might have been just an O ring needed. Anyway, just follow the video provided by this site for replacement of the valve; really easy. Biggest hassle for us was getting the dishwasher out (and back in) as it was wrapped in insulation which made the fit really tight. Thought I had everything I needed when I started but didn't have teflon tape which is needed for the brass fitting connecting the water supply to the valve (fitting is in your old valve and will be reused with the new one).

1. Shut off water supply

- Remove water line and drain hose if you need to. I was able to simply move the dishwasher forward some to do this repair without disconnecting

2. Remove access panels on the bottom.
3. Open the door
4. Remove Door Gasket carefully (do not stretch)
5. Use torque 20 driver to remove 6 screws that were under the gasket

- Some of the screws were rusted for me so I had to use kroil, a pick to clean out rust, and a hammer to help get the torque driver in enough to remove the screws. A local hardware store had replacements.

6. Use Phillips screwdriver to remove screws holding mounting brackets
7. Carefully move dishwasher out some (Careful if you have a copper water hose you may want to disconnect it)
8. Remove the strike if it is attached above the metal bar
9. Lift the metal bar and push down on the tub to make room to remove the old mounting brackets (slide them up, forward, and to the side)
10. Put new mounting brackets in place (put mounting bracket under bar, slide over into place)
11. Reverse the order at this point.

Be careful not to stretch the gasket. I soaked mine in vinegar for a bit and gently washed with dish soap to remove deposits.

1. Turned off power. 2. Unscrewed ten screws holding inside of door in place. 3. Lifted cover enough to access latch - helpful to have someone to hold this while doing the job. 4. Disconnected old latch assembly on each side - this was the hardest part as they were stiff and needed to be pulled hard. 5. Attached new latch assembly. 6. Screwed door panel back on. 7. Switched power back on. So easy and saved about $150. This stuff is NOT HARD and I just wish more people had the gumption to do repairs themselves instead of paying 'experts' to do exactly the same job.

Just inserted new basket - used butter knife to remove handle from old basket so it could be inserted on new basket. It was helpful to see comments left by others that they had same problem with their baskets and how one used a knife to remove old handle. That was a helpful hint.